Opening the refrigerator door releases this push-button switch to turn on the interior light, making stored food easier to see. When the door closes, it presses the button and turns the light off. A stuck, worn, or broken switch may leave the light off when the door is open or keep it on after closing. Replacing a faulty switch helps rest...Read moreore normal lighting control and reliable response to door movement. Disconnect the refrigerator from power before removing or installing the switch. This is an OEM part sourced directly from the manufacturer.
This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can...Read more be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance.
To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.
This spring is located on the mullion, or door flap, of your fridge. This spring is sourced from the genuine OEM manufacturer for various refrigerator models. It measures about 1.5 inches in total length, and is made entirely out of metal.
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
This is the replacement shelf glass for your refrigerator. It is made of glass and is approximately 31 inches wide and 16 inches long. The shelf glass for your refrigerator slides over the crisper cover and acts as a sort of lid. It also creates a shelf that you can place food and beverages on. If your current shelf insert glass is broken...Read more, this part is the appropriate replacement. Many of our customers have described this repair as easy. To complete the repair, carefully remove the old glass from the frame and replace it with the new pane of glass. This part is sold individually and is an authentic OEM part.
This refrigerator water inlet valve assembly controls the water supplied to the dispenser and automatic ice maker. It opens when the appliance requests water and closes when dispensing or filling ends. A cracked housing or faulty valve may cause leaks, weak dispenser flow, or prevent the ice maker mold from filling. Replacing a failed ass...Read moreembly helps restore controlled water delivery and proper shutoff between uses. The valve connects the incoming supply to the internal water system, supporting everyday dispensing and ice production. This is an OEM part sourced directly from the manufacturer.
Proper movement of the center door flap helps a French door refrigerator seal the gap between its doors. This mullion spring applies tension to the hinged flap, guiding it as the door opens and closes. A broken, stretched, or missing spring may leave the flap loose or prevent it from moving into place, making door closure difficult. Repla...Read morecing a damaged spring helps restore controlled flap movement and proper sealing. Its coiled design stores and releases force as the mullion pivots during everyday use. This is an OEM part sourced directly from the manufacturer.
The door bin is attached to the inside of the refrigerator door, and typically holds condiments, jars, and bottles. This OEM basket assembly is made of white and clear plastic. Measures approximately 16 inches long x 4 1/2 inches high x 5 inches deep. These parts should fit tightly to the door of your refrigerator, if yours is loose you ...Read moreshould replace it immediately, as it could result in its contents spilling into the inside of your refrigerator, or onto the floor.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
Keep frozen food protected from warm air leaks with this freezer door gasket. Its flexible sealing edge fits around the door perimeter and rests against the cabinet when closed, helping retain cold air and limit incoming moisture. Tears, cracks, or warped sections may cause frost buildup, condensation, or longer running times. Replacing a...Read more damaged gasket helps restore a snug seal. Before installation, smooth shipping creases with warm water and clean the retaining groove, then seat the corners first and check for even contact along every edge. This is an OEM part sourced directly from the manufacturer.
Keep ice ready for everyday drinks with this refrigerator ice maker assembly. It receives water, holds it in the mold while it freezes, and releases finished cubes into the storage bin. A worn or failed mechanism may stop making ice, leave cubes stuck in the mold, or leak around the ice tray. Replacing a faulty assembly helps restore auto...Read morematic ice production without filling trays by hand. The attached wiring harness connects the unit to the refrigerator controls. Unplug the refrigerator before removing or installing the assembly. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replace leaking water inlet valve assembly
42 of 75 peoplefound this instruction helpful.
Richard from JACKSONVILLE, FL
Really Easy
15 - 30 mins
Screw drivers
1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new
... Read morewater inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).
Read less
Was this helpful?
Thank you for voting!
Remove and replace light switch
45 of 91 peoplefound this instruction helpful.
Debbie from Waltham, MA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this helpful?
Thank you for voting!
Spring on door closer broke
11 of 17 peoplefound this instruction helpful.
Charles R from FAIRFAX, VA
Really Easy
Less than 15 mins
Pliers
Found the broken spring; matched it with parts diagram. Googled for sources via part number. Selected this site because it had best deal - price, availability, shipping. Part arrived as predicted; installed it in 2 minutes. Job done. Door now works.