Opening the refrigerator door releases this push-button switch to turn on the interior light, making stored food easier to see. When the door closes, it presses the button and turns the light off. A stuck, worn, or broken switch may leave the light off when the door is open or keep it on after closing. Replacing a faulty switch helps rest...Read moreore normal lighting control and reliable response to door movement. Disconnect the refrigerator from power before removing or installing the switch. This is an OEM part sourced directly from the manufacturer.
This lower holder cover is also known as a toe grille clip, or a kickplate clip. It is designed for use with refrigerators. The main purpose of this part is to hold the molding at the base of your refrigerator in place, it also makes removing the piece of molding simple. If you notice that the kickplate on your appliance is loose or will ...Read morenot stay in place you may need to replace one or more of these clips. This part is made of plastic, and it is sold individually.
This plastic cover is a genuine OEM replacement part for your refrigerator. This part serves as the frame the glass shelf above your refrigerator crisper. To replace this part, remove the glass shelf and existing plastic frame. Snap the new one into place and replace the shelf. This repair has been rated as easy by our customers.
This compressor start relay and thermistor assembly helps start the refrigerator's compressor and protects it from overheating during operation. It provides the electrical boost needed to get the compressor running, which is essential for maintaining proper cooling inside the refrigerator. If the refrigerator is not cooling properly, the ...Read morecompressor is not starting, or you hear repeated clicking noises, a faulty relay assembly may be the cause. Replacing this part can help restore reliable compressor operation and keep the refrigerator cooling as intended.
This part is a replacement light socket for your refrigerator. This model is white in color, and it has two sockets that will fit two separate light bulbs. The light socket connects to the power source, and the light bulb is screwed into it. If the light in your refrigerator is not working when you open the door, you could have a faulty s...Read moreocket. It is important to determine if the light bulbs are simply burned out, or if the socket is causing the issue. Be sure to disconnect your refrigerator from the power source before you begin this repair. This is an OEM part sourced directly from the manufacturer.
This part is a temperature sensing devise. It senses the rise in evaporator temperature during a defrost cycle and cycles the defrost heater off after all frost is melted. It is calibrated to permit a defrost cycle only when the temperature is below a preset temperature.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Remove and replace light switch
45 of 91 peoplefound this instruction helpful.
Debbie from Waltham, MA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this helpful?
Thank you for voting!
Refrigerator light would not reliably turn on when the door was opened.
4 of 4 peoplefound this instruction helpful.
William from TUCSON, AZ
Really Easy
Less than 15 mins
Pliers
Switched the refrigerator circuit breaker to off. Put tape around the switch to prevent scratches. Wedged the putty knife into the right side of the switch and pried up.the switch and connector popped out. Removed the connector from the old switch and connected it to the socket in the new switch. Stuffed the new switch and connector back
... Read moreinto its home. Switched on the circuit breaker. Now we have light in the refrigerator with every opening!