Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to op...Read moreerate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.
This authentic OEM high-limit thermostat, also known as a limit switch or cooling fan thermostat, serves as a safety feature to prevent the oven from overheating. It monitors the temperature inside the oven and activates the cooling fan when the temperature exceeds a certain limit. The cooling fan helps dissipate heat and maintain a safe ...Read moretemperature. The high-limit thermostat is usually situated inside the top panel. If the high-limit thermostat is broken or faulty, the cooling fan may fail to turn on, leading to excessive heat buildup inside the oven. You might also notice that your food cooks unevenly since the oven struggles to maintain the desired temperature. In some cases, if the high-limit thermostat is completely non-functional, the oven may not heat up at all. You can test the sensor at room temperature by measuring the resistance between the two prongs at the end of the sensor connector. The resistance should read approximately 1080 - 1090 ohms at room temperature. To access the thermostat, refer to your user guide for detailed instructions. Generally, you need to ensure the power is disconnected at the breaker, lift the top panel on its hinges, remove the screws on the plate under the burners, take out the burners and plate, disconnect the wires from the old thermostat, and remove the mounting screws to release it. Please note that the replacement part is sold separately from the cooling fan.
This OEM-manufactured metal temperature sensor, or oven probe, measures and regulates the temperature within the oven. If you find that your food is being overcooked, undercooked, or is not cooking evenly, the sensor may be faulty. You can verify this by testing it with a multimeter or looking out for an error code on the control board. I...Read moref you do not replace the broken sensor, your oven will run too hot or too cold. To replace the sensor, you first need to turn off the power to the oven and let it cool down. Access the probe inside the oven cavity, it is commonly attached to the rear wall. Using a screwdriver or pliers, remove any screws or clips that are securing the sensor in position. You may also need to unscrew or unclip the wire attached to the probe from the back of the oven. This sensor is sold as a single unit.
This replacement light bulb provides clear illumination to improve visibility during appliance operation. It is commonly replaced when the original bulb burns out, flickers, or no longer produces adequate light.
This broil heating element is designed to generate intense, even heat for broiling and browning inside the oven, helping achieve consistent cooking results. Featuring a multi-pass design for uniform heat distribution, it supports reliable performance during high-temperature cooking. Replacement is recommended if the broiler fails to heat,...Read more cooks unevenly, or shows visible damage such as cracks or burn spots, helping restore proper broiling function and overall oven performance.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cord was not tightened enough by delivery crew.
109 of 174 peoplefound this instruction helpful.
Timothy from Spring Valley, AL
Really Easy
15 - 30 mins
Screw drivers, Socket set
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede
... Read mored are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Read less
Was this helpful?
Thank you for voting!
The elements were not heating up
6 of 8 peoplefound this instruction helpful.
Tanya from KALISPELL, MT
Really Easy
15 - 30 mins
Screw drivers
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
Was this helpful?
Thank you for voting!
Thermostat for oven cook elements. Cooling fan is a misnomer-the fan still worked!
6 of 9 peoplefound this instruction helpful.
Betty from OLIVE BRANCH, MS
Very Easy
1- 2 hours
Screw drivers
First of all I am not Betty, I am her husband. Second I and a friend pulled the range out of the countertop (which was not necessary). The top can be raised on it hinges and the plate under the burners can be removed by taking out 8 to 19 screws and there is the thermostat looking at you. After doing this once and knowing where the thermo
... Read morestat is, the job could be done in less that an hour.. INSTRUCTIONS: Turn OFF the circuit breaker. Remove the burners. Remove the plate under the burners. Change the thermostat (making sure to place in correct direction as the one removed). Reassemble, turn on circuit breaker, test oven heat.