79043043401 Kenmore Cooktop - Overview
Sections of the 79043043401
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Main Terminal Block Kit
PartSelect #: PS471605
Manufacturer #: 5304409888
Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches...
$40.60
In Stock
Dual Radiant Surface Element
PartSelect #: PS3408889
Manufacturer #: 316282100
You can adjust the size of the burner you want to use to match your pots/pans.
$206.75
In Stock
Burner Infinite Switch - 240V
PartSelect #: PS1529263
Manufacturer #: 318293818
This infinite control switch regulates power to a surface burner, allowing smooth and adjustable heat control. Reliable switching improves cooking accuracy and safety. Replacing a faulty switch helps ...
$72.57
In Stock
Surface Burner Element - 6 Inches - 1200W
PartSelect #: PS978580
Manufacturer #: 318198817
This 6-inch surface heating element delivers steady, even heat for everyday cooking tasks. Designed for consistent performance, it is commonly replaced when a burner fails to heat, heats unevenly, or ...
$145.15
In Stock
Dual Burner Element Assembly - 1800/2600W
PartSelect #: PS978790
Manufacturer #: 318258201
This dual radiant surface bridge element is designed to supply consistent heat to the cooking surface of electric ranges and cooktops. Positioned beneath the glass top, it warms through a radiant coil...
$415.91
In Stock
Dual Infinite Element Switch
PartSelect #: PS899921
Manufacturer #: 318191024
This switch controls the stove top surface burner.
$81.35
In Stock
Common Symptoms of the 79043043401
[Viewing 5 of 5]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede
... Read more
d are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Read less
Parts Used:
-
Timothy from Spring Valley, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
109 of 174 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The smaller element of a dual element stove would not heat up.
Unplug the unit or turn off power at the electrical panel!!!! I removed the 2 screws that hold the top surface of the stove down. On my range, these are located in the front, under the the top surface. You have to open the oven door to remove them. I propped the top up with a couple of 10 inch pieces of 1 x 2 then removed the screws o
... Read more
n each end of the bracket that holds the elements in place. I used a 1/4 inch nut driver for these. With needle nose pliers, I removed the 3 retaining clips from the bracket and removed them from the element with a screwdriver and transferred them to the new heating element. The holes around the outside of the element are numbered so it's easy to know where they go. Laying the new element next to the old one, I moved each paddle-type electrical connection one at a time to the corresponding place on the new one. Put the retaining clips back in the slots. Screw the mounting bracket back in. Put the top down and secure it with screws. Very easy repair.
Read less
Parts Used:
-
Debra from DISPUTANTA, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
16 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The elements were not heating up
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
Parts Used:
-
Tanya from KALISPELL, MT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!