The surface Meduim 9.5K burner cap is located on the top of the burner head and is used in ranges and ovens. The burner cap helps spread out the burner flame for even heating, and protects the burner head from cooking spills. Without the cap you can have a burning gas torch. If your cap is missing or is discolored, replacing this part ca...Read moren solve the issue. This part comes in the color black. Remember to unplug your range from the power source and allow surface to cool before installing this part. Refer to the manual provided by the manufacturer for further installation instructions.
The function of the ignitor in your range is to create the spark that ignites the gas on the burners. If your spark ignition system is not functioning properly, you may need to replace the ignitor. This part is approximately 3 inches in length. The ignitor is located in the rear of the range, so you will need to remove the back panel in o...Read morerder to access it for this repair. Before beginning this repair, be sure that the gas valve for the range is shut off. You should also disconnect the power source to the range before you begin.
This meat probe sensor is an authentic manufacturer replacement part for cooking appliances that have a built-in meat probe feature. It is plugged into the receptacle assembly for use inside the appliance. The sensor measures the internal temperature of meat during the cooking process and sends the readings to the control panel where they...Read more can be viewed in real time. This ensures that the food is cooked to your desired level of doneness. Over time the internal sensor components may become faulty or the probe can fail due to mechanical damage resulting in inaccurate temperature readings, and failure to communicate with the control panel. Follow the sensor cable to the insertion point in the oven cavity and disconnect the faulty sensor. Install the new sensor into the insertion point and reattach the connectors to complete the repair.
This oven door light switch signals the light to turn off when the oven door closes. If your light switch is defective or you smell a burning odor, make sure to check the switch and replace it. The tool needed for this replacement is a screwdriver. Locate the switch, usually from under the oven top. Remove the wires and pull the switch ou...Read moret. Refer to the diagram provided by the manufacturer for further instructions and guidance before installation. Make sure you remember to unplug the oven from the power source before starting this repair, and wear gloves for protection.
Revamp your oven's performance with this genuine Frigidaire dual oven safety valve assembly! Specifically crafted for bake and broil burners, it is designed to safeguard and control gas flow in your oven. Prioritize safety by unplugging your range and shutting off the gas flow before installation. Always ensure gas line connections are th...Read moreoroughly leak checked post-repair. With reliable work gloves, installation becomes a safe and smooth process. Enhance your oven's functionality with the excellence of Frigidaire today!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Stove pilot not clicking on any burner, oven works fine
15 of 22 peoplefound this instruction helpful.
Colin from MORGANTOWN, WV
Easy
15 - 30 mins
Nutdriver, Pliers
Unplug the range. Remove screw to Take of the back panel on upper right corner. Unclip the old spark module, unplug the wires with the needle nose pliers and plug them into the new spark module same as the old module. Clip it on. Replace the back panel.
Was this helpful?
Thank you for voting!
Oven light stayed on & smelled like electrical burning.
16 of 35 peoplefound this instruction helpful.
Vincent from Brunswick, GA
Easy
15 - 30 mins
Screw drivers
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven lig
... Read moreht switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.
Read less
Was this helpful?
Thank you for voting!
Replace oven gas safety valve.
5 of 6 peoplefound this instruction helpful.
Hans from JERUSALEM, AR
A Bit Difficult
1- 2 hours
Nutdriver, Pliers, Screw drivers, Wrench set
It went really well until test when the flame was reaching up into the oven itself, not good. Much research finally found an older repairman who informed me the nozzle that injects the gas into the oven burner had to be fully screwed down for LP Gas. The unit is pre-set for Natural Gas. Tightened it all the way down and everything work
... Read mores just fine. We live rurally so use Liquid Propane Gas, not Natural Gas.