Models
>
79032613311
79032613311 Kenmore Range - Overview
Sections of the 79032613311
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
CAP
PartSelect #: PS11775705
Manufacturer #: 5304508442
The surface Meduim 9.5K burner cap is located on the top of the burner head and is used in ranges and ovens. The burner cap helps spread out the burner flame for even heating, and protects the burner...
$24.35
In Stock
CAP
PartSelect #: PS11775704
Manufacturer #: 5304508441
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.
$30.07
In Stock
PROBE
PartSelect #: PS16745361
Manufacturer #: 5304525427
This OEM-manufactured metal temperature sensor, or oven probe, measures and regulates the temperature within the oven. If you find that your food is being overcooked, undercooked, or is not cooking ev...
$48.85
In Stock
Steel Washer
PartSelect #: PS436497
Manufacturer #: 316008401
This steel washer is also known as the range washer and is used on your oven door. The measurements for the steel washer are a three quarter inch outer diameter, and a one quarter inch inner diameter....
$11.23
In Stock
Igniter/Orifice Mounting Screw
PartSelect #: PS440022
Manufacturer #: 316240600
This part is the igniter/orifice mounting screw for your cooktop or range. It is approximately ½ an inch in length and is made of metal. The mounting screw connects the orifice to the cooktop. If the ...
$12.23
In Stock
CAP
PartSelect #: PS11775706
Manufacturer #: 5304508443
This black burner cap is a genuine OEM part made of a durable material capable of reaching 14,000-BTU, with an approximately 3-inch diameter. It is compatible with various models of ranges and cooktop...
$35.49
In Stock
REGULATOR
PartSelect #: PS16218309
Manufacturer #: 5304521339
This valve automatically cuts off the flow of gas at a certain pressure.
$77.98
In Stock
Questions And Answers for 79032613311
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 79032613311
[Viewing 6 of 6]Oven is too hot
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas smell
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replacing the fan on a convection oven (fan was making a vibration noise)
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. O
... Read more
nce there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.
Read less
Parts Used:
-
John from Stevensville, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
16 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Regulator had propane leak past diaphragm
removed two screws disconnected inlet pipe and two outlet pipes, removed regulator. Replaced with new regulator. performed leak Test.
Parts Used:
-
Albern from Bainbridge IS., WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Wrench set
14 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove pilot not clicking on any burner, oven works fine
Unplug the range. Remove screw to Take of the back panel on upper right corner. Unclip the old spark module, unplug the wires with the needle nose pliers and plug them into the new spark module same as the old module. Clip it on. Replace the back panel.
Parts Used:
-
Colin from MORGANTOWN, WV
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
15 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!