This evaporator fan blade moves cooled air through the refrigerator or freezer compartments when driven by the fan motor. A cracked, warped, or loose blade may vibrate, strike nearby parts, or fail to move enough air. Unusual ticking or humming noises and warmer compartment temperatures may be reasons to inspect the fan assembly. Check fo...Read morer ice buildup and motor or mounting problems as well, since these can cause similar symptoms. Disconnect power before accessing the blade and follow the appliance instructions for fitting it securely on the motor shaft. This is an OEM part sourced directly from the manufacturer.
This water valve kit, also known as a single outlet water valve kit, is used in refrigerators. The kit includes a union, two screws, and some tubing pieces. If one of the solenoids in your water valve is not allowing water to flow into the icemaker or the dispenser, it might be damaged or broken. If this is the case, it is best to replace...Read more this part. To repair, first remove the cardboard panel at the rear of the fridge. Next, remove the tubing that supplies water to the valve with a 1/2 inch wrench. Once it is accessed, refer to the manual guide provided by the manufacturer for further installation instructions and guidance.
This plastic ice cube tray holds water for freezing into 12 cubes at a time. Channels help water spread evenly during filling, while corner supports allow trays to stack securely in the freezer. The tray measures approximately 11 inches long and 4.5 inches wide and is sold individually. Its flexible design allows frozen cubes to be releas...Read moreed by hand. Cracks or splits may let water leak before it freezes and are reasons to replace the tray. Check the available freezer space against the tray dimensions before ordering. This is an OEM part sourced directly from the manufacturer.
A cold-water connection to the ice maker is the job of this 6-foot stainless steel waterline. This OEM installation kit includes a 1/4-inch compression union and thread sealant. Turn off the cold-water supply before installation. After restoring the supply, inspect the connections for leaks. Avoid kinking the line or overtightening the connections.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Icemaker Wasnt Making Ice
12 of 16 peoplefound this instruction helpful.
ERIC from SAN ANTONIO, TX
Really Easy
15 - 30 mins
Nutdriver, Pliers
After unplugging electric cord and turning off water at wall, I then removed the two screws that secured the valve to the refrigerator. I then removed the water connections to the valve and removed a short portion of the hose going to the icemaker. I then installed the connection pieces provided package and reversed the procedures to
... Read more install the new part. It was easier than I thought it would be.
Read less
Was this helpful?
Thank you for voting!
ice maker did not work.
6 of 7 peoplefound this instruction helpful.
LARRY from HANOVER, MD
Easy
15 - 30 mins
Nutdriver
I pulled the cover from back of fridge then removed two screws from the water valve disconected the wires and removed water lines. had to reroute water lines so the universal part would fit. don't forget to turn off the water befor doing the above. found new mounting hole and reconected water lines. worked like a champ.
Was this helpful?
Thank you for voting!
Fridge made a hellacious noise and wasn't cooling well
5 of 5 peoplefound this instruction helpful.
Bruce from MARTINEZ, CA
Really Easy
Less than 15 mins
Nutdriver
From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.
After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to
... Read moreuncouple.
I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.
I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.