The interior light in your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, or stays on when the door is closed, you could have a faulty switch. The switch is spring-loaded and is a generally closed type of switch meaning there should be no continuity...Read more when the button is pushed, and continuity through the switch when it is no longer engaged. This plastic, white, OEM switch is sourced directly from the manufacturer, is sold individually and is easy to replace. The repair usually takes less than 15 minutes and requires a flat-blade screwdriver and needle-nose pliers.
This lamp cover is also commonly referred to as a light lens. This is a genuine replacement part. It is used in a refrigerator to cover the light bulb. It is made of clear plastic. It measures 14 inches by 5 1/2 inches. This does not include the white plastic housing that the light is in, this is just the cover. To install your replacement part you simply snap it into place, no tools are required.
Illuminate your LG refrigerator with this genuine light assembly housing cover. Designed with precision, this component not only houses but also safeguards the light bulb in your appliance. For your safety, remember to unplug your refrigerator and safely store any perishable items elsewhere before beginning the installation process. Alway...Read mores wear work gloves during the replacement for extra protection. This specific light lens lamp cover is typically positioned at the top of the refrigerator compartment. Please double-check your model to ensure this part is the right fit.
This part is a replacement light socket for your refrigerator. This model is white in color, and it has two sockets that will fit two separate light bulbs. The light socket connects to the power source, and the light bulb is screwed into it. If the light in your refrigerator is not working when you open the door, you could have a faulty s...Read moreocket. It is important to determine if the light bulbs are simply burned out, or if the socket is causing the issue. Be sure to disconnect your refrigerator from the power source before you begin this repair. This is an OEM part sourced directly from the manufacturer.
This fan assembly circulates air through the appliance to support proper temperature control and ventilation. Designed for quiet and efficient airflow, it is replaced when airflow weakens, noise increases, or cooling performance declines.
This defrost temperature sensor and thermistor assembly is designed to monitor the temperature of the evaporator coils in your refrigerator, ensuring the defrost cycle activates accurately and efficiently. The thermistor functions as a variable resistor, sending precise temperature readings to the control board to prevent overheating and ...Read moreexcessive frost buildup. This assembly includes a fuse and wire harness for easy installation.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Remove and replace light switch
45 of 89 peoplefound this instruction helpful.
Debbie from Waltham, MA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this helpful?
Thank you for voting!
Replace Thermistor in back of freezer
17 of 24 peoplefound this instruction helpful.
Scott from JUPITER, FL
Easy
1- 2 hours
Pliers, Screw drivers
Turn off power, remove upper and lower drawers (may need to open upper refrigerator doors to remove large freezer bin,) remove drawer supports (upper and lower), remove rear freezer panel (trick is to loosen 4 screws on fan bumpout to get the panel to come free from the freezer side wall), test thermistor with multimeter (should have cont
... Read moreinuity or near zero resistance across 2 orange fuse wires) before cutting zip ties, cut zip ties holding Thermistor in place, remove old Thermistor, install new Thermistor, install new zip ties, replace rear freezer panel, install upper and lower drawer supports, install drawers, turn on power, should be fixed if error code doesn't return after 6 hours.
Read less
Was this helpful?
Thank you for voting!
Warped and melted lamp cover
5 of 5 peoplefound this instruction helpful.
Brad from MUSCATINE, IA
Really Easy
Less than 15 mins
Screw drivers
Remove 2 screws and then disconnect wires to the bulb sockets. Reconnect the wires Reinstalled lamp case , tab end first then replaced the 2 screws and the Lens cover. In addition, I changed out the incandescent bulbs to a much cooler LED bulb.