74409CP Toro Lawn Mower - Overview

This OEM Push Rod is a silver, metal part, approximately 5.5 inches long. It can be installed using a wrench or sockets. A Spark Plug Gap Tool may also be needed for maintenance. The installation of this partis rated as Medium difficulty by customers. It attaches inside the cylinder head, and is installed by tightening the rocker nut on...Read more top to manufacturer specs. This part opens and closes the intake and exhaust valves, and if broken there will be poor engine performance as well as an internal knocking or tapping sound from the engine. If damaged, likely due to fatigue or stress, it must be replaced. Refer to your owners manual or model number to ensure you are slecting the correct part.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

Kawasaki 10W-40 4-Cycle Oil. Kawasaki KTECH 4-cycle oil is enhanced with Anti-Foaming and Anti-Sheer agents, along with other additives.

This genuine oil seal is a brown, rubber part, measuring 8 x 14 x 5mm. This part can be installed using a screwdriver, wrench set, pliers, and pick, and a seal puller may also be required for maintenance. This repair is rated as "Easy" to install by customers. It attaches to the governer shaft to provide a tight seal, and if broken due ...Read moreto general wear or drying out, there will be visible oil coming out around the shaft. If damaged or missing, it should be replaced. Check your owners manual for the correct part number.

This Gasket-Rocker Case is a grey, individually sold part, direct from the original equipment manufacturer. It requires only a socket to install and is rated as Easy to install by customers. This part is installed between the valve cover and cylinder head, by torquing in an alternating pattern to the manufacturer specifications for a pr...Read moreoper seal. It provides a tight seal between the cylinder head and valve cover, and if broken due to general wear, you will see oil leaking around it. This part should be replaced if broken, or if removing the valve cover for other repairs as the gasket can only be used once. Only a visual inspection is needed to check for leaks. Refer to your owners manual or model number to ensure you are selecting the right part.

This genuine ignition coil assembly—also known as an armature-magneto—is a direct replacement part sourced from the original equipment manufacturer for use with Kawasaki engines. It plays a critical role in the ignition system by generating high-voltage pulses that power the spark plugs, ensuring reliable engine startup and performance. T...Read morehe assembly is made of durable metal and features a rubber-insulated wire with a spark plug boot for secure connection and long-lasting use. Replacing the ignition coil is a straightforward repair that requires only a screwdriver, a set of wrenches, and pliers. Begin by disconnecting the spark plug wire and removing any covers or components blocking access to the coil. Use your tools to detach the old coil, then install the new one in its place, ensuring all connections are secure. Once reassembled, your engine should be ready to run smoothly again. Ignition coil generates the voltage for the spark plug. Wear work gloves to protect your hands when installing this part.

This screw is an authentic OEM sourced hardware, it is not an aftermarket imitation. It is commonly utilized on Toro snow throwers. It is a standard hardware which has multiple uses depending on your unit, please make sure to check appropriate diagrams for correct location and use of this hardware. One hex head screw is included per order.

This genuine replacement part is sourced directly from original equipment manufacturer. It is specially designed for use with Kawasaki engines. Its purpose is to make an air tight seal for the manifold. Over time this gasket will deteriorate allowing for leaks, at this point it should be replaced. This item is made out of composite material and it is sold individually. To complete this repair you will need a wrench.

This OEM Fuel Filter is a white, individually sold, plastic part, which measures 3 x 1.25 inches. It can be installed using pliers and is rated as Easy to install by customers (Tip: Make sure the fuel clip is secure when installing). This part is attached along the fuel line, between the fuel tank and carburator, and is used to filter c...Read moreontaminents out of the fuel. If broken fuel will leak, and it will smell. If clogged, there will be no fuel flowing out of it. If broken or clogged, it should be replaced. It should also be replaced during regular maintenance. Check your owners manual or model number to ensure you are selecting the right part.

This O-ring, also known as a round seal, is an authentic OEM part used in lawn and garden equipment. It is a small, circular, rubber ring that helps create an airtight seal between the oil filter filler and engine to prevent leaking and ensure adequate lubrication. It is common for the O-ring to become brittle and lose its elasticity due ...Read moreto aging, and exposure to chemicals and high temperatures in the equipment. If an O-ring fails, it can result in oil leakage, leading to reduced equipment performance, and potential damage to the surrounding components. Carefully the oil ring off the sealing surface and clean the area thoroughly to ensure a proper seal for the new O-ring. Lightly lubricate the new O-ring and press it on to the sealing surface.