74296 - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

This is a genuine Broil-Mate, Broil King, Huntington, and Sterling part sourced directly from the manufacturer for use in gas grills. The grease shield goes next to the inner rear panel. A wrench and a screwdriver may be necessary during the installation of this item. It may become broken and will need to be replaced. This is made of metal and is available as an individual replacement part.

It is a genuine OEM item that is made for Toro lawn and garden equipment. This is a special component which helps to provide a tight fit between connected parts. Unfortunately, over time it may wear out, get damaged or lost eventually requiring a replacement. This high-quality bushing is made of durable material and is sold as an individu...Read moreal item. To ensure the proper repair procedure, check the parts diagrams for your specific model.

This is a genuine OEM sourced hardware that is specifically made for use with Toro lawn and garden equipment. It is a standard hardware which may have multiple applications depending on the model of your unit. Please make sure to refer to the appropriate diagrams for the correct location and application of this part. Keep in mind this hig...Read moreh-quality flange nut is made of durable metal and is sold individually. Note, you will need a wrench to secure or remove it.

This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it becomes lost or broken and may require a wrench during installation. This is an OEM Toro part sourced directly from the manufacturer and used in snowthrowers.

This is an authentic replacement part manufactured for use with Toro snowthrowers. The ni lock nut is designed to prevent from being unthreaded from vibration. This nut is used with several different models of snowthrowers and is used with various applications. The nut is sold as an individual replacement part, please see model diagram for associative parts.

It is made of metal and is sold individually. The screw connects to the idler pulley. A socket set might be needed during the installation process. Over time this part may become stripped and will need to be replaced. This part is an OEM from Toro and Lawn Boy for use in snowthrowers, tillers, blower-vacuums, and lawn tractors.

This replacement hardware is sourced from original equipment manufacturer for use with Toro snowthrowers. It is standard hardware which has multiple applications, please refer to appropriate diagrams for correct location and use of this locknut. This part is made from durable metal and it is sold individually.