74274 Toro Lawn Mower - Overview

This is a replacement screw, also known as a shear pin that is used in several pieces of outdoor power equipment. It is made of metal and is approximately 2 inches in length. It is a hex head screw and is sold individually. This is an OEM part sourced directly from the manufacturer.

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This oil seal is an OEM replacement part designed to prevent oil from leaking from the engine or gearbox while keeping contaminants from entering. It is used in various lawn mowers where it ensures that the moving parts in the mower remain adequately lubricated and protected from dirt/debris. The oil seal can wear down due to aging, heat,...Read more pressure, or improper installation. If the seal is no longer functioning oil will leak, the engine will overheat, and its internal components will wear down due to excessive friction. Use seal pullers to remove the seal from its housing on the engine crankshaft or transmission housing. Clean the surrounding area using a cloth or soft brush to prevent contamination and ensure a good seal. Apply oil to the lip of the new seal and firmly press into position until it is flush against the sealing surface. Once you have completed the repair, run the lawn mower to check that there are no longer any leakage or performance issues.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

It is a genuine OEM item that is made for Toro lawn and garden equipment. This is a special component which helps to provide a tight fit between connected parts. Unfortunately, over time it may wear out, get damaged or lost eventually requiring a replacement. This high-quality bushing is made of durable material and is sold as an individu...Read moreal item. To ensure the proper repair procedure, check the parts diagrams for your specific model.

This is a genuine OEM sourced hardware that is specifically made for use with Toro lawn and garden equipment. It is a standard hardware which may have multiple applications depending on the model of your unit. Please make sure to refer to the appropriate diagrams for the correct location and application of this part. Keep in mind this hig...Read moreh-quality flange nut is made of durable metal and is sold individually. Note, you will need a wrench to secure or remove it.

This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it becomes lost or broken and may require a wrench during installation. This is an OEM Toro part sourced directly from the manufacturer and used in snowthrowers.

The flat washer is an OEM replacement part that provides a wide surface area to distribute the load of a bolt or a screw when it is installed. This protects the part being fastened from getting damaged or deformed and provides a more secure fit for the bolt/screw. This flat washer is made of steel and has a diameter of 0.375 inches and a ...Read morethickness of approximately 0.063 inches. To replace the flat washer, first unthread the bolt/screw before using a flathead screwdriver to carefully pry it off. Clean the area, place the new flat washer in position, and thread the bolt/screw back on. Sold individually.