74177 Toro Lawn Mower - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

This replacement push rod is specially designed for Kohler engines commonly installed on a variety of lawn and garden equipment. It is an authentic high-quality item that is sourced from the original equipment manufacturer. The rod is attached to the camshaft to push the exhaust valve open during the exhaust stroke. A bent pushrod can not...Read more only affect your engine\\\'s performance, but it can also seriously damage other parts if the problem is not taken care of immediately. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. It is made of durable metal and is sold individually. You will need a screwdriver and a wrench set to take the engine apart in order to perform this repair.

Kohler Original Equipment 52 050 02-S Pro Performance Oil Filter. For optimum performance, we recommend changing the oil in your small engine after the first five hours of use. After that, change the oil on a yearly basis or after every 50 hours of use (whichever comes first).

This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it becomes lost or broken and may require a wrench during installation. This is an OEM Toro part sourced directly from the manufacturer and used in snowthrowers.

The flat washer is an OEM replacement part that provides a wide surface area to distribute the load of a bolt or a screw when it is installed. This protects the part being fastened from getting damaged or deformed and provides a more secure fit for the bolt/screw. This flat washer is made of steel and has a diameter of 0.375 inches and a ...Read morethickness of approximately 0.063 inches. To replace the flat washer, first unthread the bolt/screw before using a flathead screwdriver to carefully pry it off. Clean the area, place the new flat washer in position, and thread the bolt/screw back on. Sold individually.

This is an authentic replacement part manufactured for use with Toro snowthrowers. The ni lock nut is designed to prevent from being unthreaded from vibration. This nut is used with several different models of snowthrowers and is used with various applications. The nut is sold as an individual replacement part, please see model diagram for associative parts.

It is a genuine OEM sourced replacement part which is specially designed for use with Toro snowblowers. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality screw is made of durable metal and is sold individually.

This stator kit (15 amp) is an OEM part direct from Kohler. Composed of metal, wiring and protective plastic, the kit is made for use with many small engines. This component provides the necessary voltage for charging the motor battery. A wrench and a pair of pliers are helpful for making the installation. Please refer to the manual for additional repair instructions.