74170 - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

This is an authentic OEM sourced replacement part, it is specially made for use with lawn and garden equipment. It is a standard hardware which has multiple applications depending on your model, please refer to appropriate diagrams for correct location and use of this item. Please note this high-quality hex head screw is sold individually.

This OEM Push Rod is a silver, metal part, approximately 5.5 inches long. It can be installed using a wrench or sockets. A Spark Plug Gap Tool may also be needed for maintenance. The installation of this partis rated as Medium difficulty by customers. It attaches inside the cylinder head, and is installed by tightening the rocker nut on...Read more top to manufacturer specs. This part opens and closes the intake and exhaust valves, and if broken there will be poor engine performance as well as an internal knocking or tapping sound from the engine. If damaged, likely due to fatigue or stress, it must be replaced. Refer to your owners manual or model number to ensure you are slecting the correct part.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

This Gasket-Rocker Case is a grey, individually sold part, direct from the original equipment manufacturer. It requires only a socket to install and is rated as Easy to install by customers. This part is installed between the valve cover and cylinder head, by torquing in an alternating pattern to the manufacturer specifications for a pr...Read moreoper seal. It provides a tight seal between the cylinder head and valve cover, and if broken due to general wear, you will see oil leaking around it. This part should be replaced if broken, or if removing the valve cover for other repairs as the gasket can only be used once. Only a visual inspection is needed to check for leaks. Refer to your owners manual or model number to ensure you are selecting the right part.

This genuine OEM sourced replacement fuel tank is a high-quality item that is specially designed for use with Husqvarna handheld lawn and garden equipment. Its purpose is to hold the fuel that is needed for the engine. Over time the tank may get damaged or lost eventually requiring a replacement. It includes the fuel tank, the cap, the fu...Read moreel lines and the clamps to secure them. Make sure to drain the gas tank before starting the repair.

This replacement oil filter is specially designed for use with Kawasaki engines. It is a genuine OEM sourced part, not an aftermarket immitation. This oil filter is used to remove contaminants from the engine oil. This part is manufactured in accordance with applicable EPA emissions regulations. It is recommended to replace oil filters at...Read more least once a season. Please note, this item is sold individually. To replace the oil filter you will need a pipe wrench or a filter wrench. • Disconnect the spark plug • Remove the old oil filter by twisting it counterclockwise • Clean the sealing surface on the oil filter adapter from any dirt or debris • Lightly oil the filter gasket with clean engine oil • Install the new filter

This solenoid is an authentic manufacturer replacement part for use in lawn tractors. It sends the electrical current from the battery to the motor to allow the tractor to start and run. The solenoid will need to be replaced if it is damaged or experiencing electrical failure. Signs of a failed solenoid include difficulties cranking the e...Read morengine, hearing clicking or no sound at all when turning the ignition key, and a starter that cannot stop running. Begin the repair by disconnecting the battery for your safety. Take a note/picture of how the wire connectors are routed before disconnecting them. Remove the bolts that secure the solenoid in place and pull the faulty part out. Position the new solenoid in its place and secure it with the mounting bolts. Use your notes to reconnect the wiring and battery.

This O-ring, also known as a round seal, is an authentic OEM part used in lawn and garden equipment. It is a small, circular, rubber ring that helps create an airtight seal between the oil filter filler and engine to prevent leaking and ensure adequate lubrication. It is common for the O-ring to become brittle and lose its elasticity due ...Read moreto aging, and exposure to chemicals and high temperatures in the equipment. If an O-ring fails, it can result in oil leakage, leading to reduced equipment performance, and potential damage to the surrounding components. Carefully the oil ring off the sealing surface and clean the area thoroughly to ensure a proper seal for the new O-ring. Lightly lubricate the new O-ring and press it on to the sealing surface.

This is a genuine replacement part that has been sourced from the original manufacturer to be used with snow thrower engines from Husqvarna and Toro. The metal screw is used to fasten the fuel tank to the tank mounting bracket. This item is available as an individual replacement part, please note a hex socket wrench may be needed to install this item.