74024 (ABICSE2) LG Refrigerator - Instructions

For this model the ice maker is very easy to replace. All it takes is a phillips head screwdriver. There are two wire connections you have to unplug. Easy out easy in. You do not have to disconnect the water line, just make sure the line is lined up correctly when you reinstall the new icemaker. It seems to take approximately 8 hours befo ... Read more re you start getting ice again. If you have this same model, you already know this ice maker is very slow in making ice and is not able to keep up with daily usage of ice for a household of 3.

The Ice Maker from Part Select was complete. Plastic housing, Ice maker located at the top and ice cruncher/dispenser at the bottom.
Note: Both the ice maker and the dispenser wiring goes to a common connecter. It is not advisable to plan changing out only one of these.

Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.

Some have said that the installation took 5 minutes. Mine took less than that, and I did it with one hand. I had a beer in my other hand.

Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary w ... Read more aste of time and labor.

Watched a couple of YouTube videos and then went at it

Very easy. Just slipped it back into place

Un-wrapped the basket......Installed with NO tools......

Removed old gasket from the door and replaced with new gasket.

Remove 3 screws bottom and base.
Loosen top screw. Pull out from bottome and unplug wire harness.

Opened the box. Removed wrapping. Washed the new part. Unloaded old basket. Removed old basket. Set in new basket. Loaded new basket. Closed the door. Even an 80 year old can do it!

Removed screws from broken Multi Ducts, pulled broken pieces from ice maker and replaced new Multi Ducts.

I started by emptying the food out of the refrigerator. Because of the placement of the refrigerator, it was hard for me to open the doors all the way, but I managed to remove the vegetable drawer, the fruit drawer, the deli drawer drawer, and glass that goes in the tray. Once that happened, I realized my refrigerator was a biology experi ... Read more ment in progress.
Using my steam cleaner, I cleaned everything that I could and the refrigerator actually looked almost brand new.
I removed the deli tray to have more room to get the whole tray and side guides . Once you do that. the tray is actually very easy to replace. The guides were still in pretty good condition although I ordered one more because it did have a small crack and eventually it will break.
You remove the three guides (left, right, and center) from the old tray and attach the new tray fram.
Sounds Easy, right?
It takes a bit of finagling because " the magic tray" which is part of the vegitable drawer has to be placed before you put the right guide on. this process is a bit awkward. if you can get an extra hand, it helps. After that, it was very easy to just put things back and I took this opportunity to clean the rest of my refrigerator and re-organize. I am going have to do this again because I have to replace the right guide, which has a crack, but so far it's working great it is not a problem. Nothing that a little duct tape can't solve until the real thing comes along. This project took longer than I thought it would. But that was primarily because I also cleaned the refrigerator, and put the right guide on before I figured out I had to put the humidifier cover in first. I think that's really the key step here.
I leave you with this: I researched how to find these parts and this site t was great. I can replace all of the hardware that breaks in my refrigerator for less than it costs to buy a new refrigerator. My friend felt I should just dump the refrigerator and start new. As other DIY people, that was like fingernails on a chalkboard for me. It's wasteful to the environment and economically unfeasible. So celebrate your project's end!

Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.

Removed the old one and replaced with the new.