72509 - Overview

This is a high quality replacement hardware that is specially manufactured for use on Toro lawn and garden equipment. Two of these screws are generally used to secure the belt guide to the mower deck. Please note this durable metal hex head taptite screw is included per order.

A washer is used for things such as load distribution, stability, alignment and protection for whatever equipment it is fastened between. This curved washer, also known as a wave washer or spring washer, is made of metal and features a curved design that allows for applications in settings where objects being fastened together are also cu...Read morerved or to exert a continuous level of tension. This washer measures approximately 1-inch in outer diameter and 1/3-inch inner-diameter and is compatible with and used on equipment like snowblowers, chainsaws and lawnmowers. This washer is installed between a round fastener or knob to better secure them together and if you notice that where the washer is normally connected is loose or vibrates excessively, this washer likely needs replacing. Depending on your model the replacement process may appear different, but it is just as simple as placing the washer between two things that are connected and securing them tightly.

This genuine OEM oil filter helps to remove harmful contaminants from engine oil. It is designed for a variety of Engines. It is sold Individually. This part maintains optimum performance of your engine in accordance with applicable EPA emissions regulations. It is recommended to replace an Oil Filter at least once a season.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

This replacement push rod is specially designed for Kohler engines commonly installed on a variety of lawn and garden equipment. It is an authentic high-quality item that is sourced from the original equipment manufacturer. The rod is attached to the camshaft to push the exhaust valve open during the exhaust stroke. A bent pushrod can not...Read more only affect your engine\\\'s performance, but it can also seriously damage other parts if the problem is not taken care of immediately. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. It is made of durable metal and is sold individually. You will need a screwdriver and a wrench set to take the engine apart in order to perform this repair.

This oil seal is a genuine OEM replacement part designed for lawn and garden equipment. It is a small, circular rubber seal with a diameter of 2 3/8 inches, used to prevent oil leakage between the gear cover and gear shaft, and prevent the entry of contaminants. You will need to replace this oil seal if it is brittle, cracked, or has lost...Read more elasticity. A faulty seal will cause the gears to lose lubrication, increase friction damage, and prematurely wear down the parts. Remember to drain the oil from your equipment before beginning any repairs. Carefully pry the old seal from its mounting position and clear off any debris and residue on the area. Place the new seal in position and ensure it is securely fitted.

This is a genuine Kohler replacement part that has been sourced from the original manufacturer to be used with small engines. The metal screw is used to secure the head to the top of the cylinder assembly. This screw requires a hex ratchet set to install and is priced as a single item.

This OEM part is sold individually and is a direct replacement part sourced from the manufacturer. The Woodruff Key is used to allow mating parts such as a shaft and gear to rotate together. It is made of silver-colored metal and is found in various locations, depending on your model. This part will wear over time and needs to be replace...Read mored when damaged, worn, or if the mating parts no longer rotate together. Customers rate this repair as Easy.

This screw is an authentic OEM sourced hardware, it is not an aftermarket imitation. It is commonly utilized on Toro snow throwers. It is a standard hardware which has multiple uses depending on your unit, please make sure to check appropriate diagrams for correct location and use of this hardware. One hex head screw is included per order.

Made of durable black rubber, this Oil Seal is an authentic OEM part for use in over 150 models of small engines. This part is sold individually, not as part of a kit or assembly. It will be found on the crankcase opening, where the crankshaft is. The Seal should be replaced when it becomes worn or damaged. When it malfunctions, you'll s...Read moreee oil visibly leaking. To complete this repair, you will need a screwdriver, pliers, a socket set, a wrench set, a nut driver, and an impact wrench. Customers rated the difficulty of this repair as Expert.

This authentic replacement part is supplied directly from the original equipment manufacturer for use with Kohler engines commonly installed on lawn and garden equipment. Please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this part is made of high-quality metal and is sold individually.