This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
This door basket assembly is supplied by the original manufacturer to provide storage for various food items in refrigerators. It consists of a white plastic base and a transparent shield, measuring 14.5 inches in length and 4 inches in width. The basket is securely attached to the right side of the refrigerator and offers a compartment f...Read moreor organizing items such as bottles, jars, and condiments. The door basket assembly helps maximize storage space and allows you to easily access frequently used items. However, the door basket will need to be replaced if the plastic becomes cracked, deformed, or broken. Using a faulty door basket may result in items falling out, and potential damage to the door frame. Detach the old basket assembly from the refrigerator and snap the new one in place. Ensure that the new assembly is securely fitted before placing items in it.
Refrigerator Air Filters are a key component for neutralizing odors and ensuring a fresh stream of air into your refrigerator. Swapping your old filter out for a fresh one isn’t difficult and should take less than five minutes. This OEM filter measures approximately 3 inches (length) x 3 inches (height) x 5 inches (Depth). Air filters should be changed every 6 months depending on usage.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
Frost near the door or a freezer that runs often may have a damaged door seal. The flexible gasket blocks room air and moisture from entering the cold compartment. First clean the seal and contact surface, then check the hinges and door fit. Match the replacement to the complete freezer model and door position. If shipping leaves folds, s...Read moreoak the gasket in warm water for 5 to 10 minutes or use a hair dryer on low. Do not overheat the rubber. Smooth each side, close the door, and test the seal with a strip of paper.
This is a micro switch for various models of LG refrigerators. This switch is responsible for turning the ice dispenser on and off within the freezer compartment of the fridge. If this switch is damaged or shorted, it will cause the ice maker to work inconsistently, or not at all. This switch is different from the water dispenser switch, ...Read morewhich has an entirely different shape all together. Replacing this switch is simple and only requires a Philips-head screwdriver to disconnect the old switch and install the new one. This switch is a genuine OEM LG part and does not come with any other parts or accessories.
This fridge gasket, also known as a door seal, is an authentic OEM part supplied by LG for use with various models of LG refrigerators. It is a flexible strip of rubber that sits along the perimeter of the refrigerator. It creates an airtight seal between the door and fridge body to prevent cold air from escaping and warm air from enterin...Read moreg. This helps to keep your fridge cool and energy efficient. If the gasket is worn out, torn, or can no longer maintain a tight seal, your fridge will have to work harder to maintain the correct temperature inside the fridge. You may also notice that the door may not be able to close properly.
NOTE: The Secondary (smaller) wire connector has 3 wires in it. If original ice maker has 6 wire connector see part number AEQ73110205. Please verify connector before ordering.
This water inlet valve in your refrigerator, also called a solenoid valve or water control valve, regulates water flow to the icemaker and dispenser. It is found at the rear of the appliance, where it connects to the household water supply line. It uses electrical solenoids to control the flow of water. It needs to be replaced when your f...Read moreridge has a lack of ice production, an inactive water dispenser, or water leaks around the supply line. Please keep in mind that this genuine OEM replacement part is sold separately from the water line.
This water tubing clip holds the water fill tube in place in your refrigerator. The water fill tube attaches and supplies water to the ice maker/water dispenser in your fridge-freezer. If the tubing is in working order, but is hanging loose inside the unit, the issue could be that the clip meant to hold it in place is broken. If this is t...Read morehe case, you should look to replace the clip. This clip is made of black plastic, and is just over half an inch long. This is a genuine OEM replacement part, and is sold separately.
This refrigerator water filter and filter assembly is designed to improve the quality of drinking water and ice by reducing contaminants such as chlorine, lead, and sediment. Certified to NSF standards 42 and 53, it enhances taste and clarity while allowing beneficial minerals to pass through. Compatible with select bottom-freezer refrige...Read morerator models, this genuine replacement part should be installed using a simple twist-in method and replaced every six months or when water flow slows. After installation, flushing approximately four gallons of water ensures optimal performance and removes any residual carbon particles. Regular replacement supports consistent filtration and helps maintain the appliance’s performance.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice maker needed replaced
3 of 3 peoplefound this instruction helpful.
Lee from BELTON, TX
Very Easy
Less than 15 mins
Screw drivers
Removed 4 screws then removed ice maker unit. Unplugged the old unit. Checked and verified the inlet tube was clean and not blocked. Plugged in the new unit. Placed unit into proper location and verified it was properly in place. Replaced the 4screws. Turned on the unit closed the ice door and it started making ice maybe an hour later by
... Read moremorning the ice bucket was full. Super easy.
Read less
Was this helpful?
Thank you for voting!
Ice maker wore out.
3 of 3 peoplefound this instruction helpful.
Thomas from LA PLACE, LA
Really Easy
30 - 60 mins
Screw drivers
I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction. I did receive a credit for the defective part. VERY Satisfied with y’all’s service. Waiting for return i
... Read morenstructions if y’all still want it back. Thanks, Thomas Pennebaker
Read less
Was this helpful?
Thank you for voting!
Left side gasket was torn and would seal properly
3 of 4 peoplefound this instruction helpful.
Thomas from CHULA VISTA, CA
Easy
Less than 15 mins
Screw drivers
Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.