71606 (ATICSE0) LG Refrigerator - Instructions

Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.

Turn off power, remove upper and lower drawers (may need to open upper refrigerator doors to remove large freezer bin,) remove drawer supports (upper and lower), remove rear freezer panel (trick is to loosen 4 screws on fan bumpout to get the panel to come free from the freezer side wall), test thermistor with multimeter (should have cont ... Read more inuity or near zero resistance across 2 orange fuse wires) before cutting zip ties, cut zip ties holding Thermistor in place, remove old Thermistor, install new Thermistor, install new zip ties, replace rear freezer panel, install upper and lower drawer supports, install drawers, turn on power, should be fixed if error code doesn't return after 6 hours.

The Refrigerator now runs very quite.
After watching several videos I started on mine and found that it was a bit different than any in the videos. However all but the back panel was shown and that was helpful.
The back panel was a bit difficult but a hair dryer seemed to help .
All in all it was a good choice to do it myse ... Read more lf as it was done quicker than waiting on a repair man.

This couldn't have been easier. Two tiny screws in the front needed unscrewed, and then two plastic clips in the middle just had to be popped lose. Finally, you unplugged the power cord. Then, you just needed to reverse the process by plugging the new ice maker in, popping the clips in place, and screwing the two holes back in and turning ... Read more the whole thing on. Voila! Perfect ice cubes again. And for only a little over $100.

Take out 2 screws and unplug unit before removing. Plug-in new unit and screw in 2 screws. That's it.

1) Remove three drawers and items sitting on glass shelf.
2) Remove glass shelf
3) Remove entire crisper plastic unit from refrig.
4) Unscrew 6 screws holding uprights with a philips head screwdriver.
5) Remove top frame and replace with new frame.
6) Replace 6 screws and tighten them.
7) Replace entire frame ... Read more in refrig and replace 3 drawers and glass shelf.
8) Done

I followed the directions! It was so easy that I bought another switch for my sister's fridge (same as mine). Her light was out too!

Switched the refrigerator circuit breaker to off. Put tape around the switch to prevent scratches. Wedged the putty knife into the right side of the switch and pried up.the switch and connector popped out. Removed the connector from the old switch and connected it to the socket in the new switch. Stuffed the new switch and connector back ... Read more into its home. Switched on the circuit breaker. Now we have light in the refrigerator with every opening!

Have had the Sears repairman come to the house to replace this part in 5 minutes for +$100.. twice. When my dad's stopped working, ordered the part and replaced it myself for the cost of the part and shipping.
Use a screw driver to pry the right side of the switch and pull out. Best to watch a youtube video first. Takes about 5 minut ... Read more es.

After watching a few iTunes videos I was able to order the light switch from part select and within a week I had the new switch. I had a little trouble getting the switch out. I used a flat screw driver and taped around the edge to keep from damaging the wall inside. I found the clip on the right side and had to use some force to get it p ... Read more opped out, you may need to use pliers to disconnect the switch.

Ordered the Part after looking at the choices shown, once I inspected the unit. I then knew by looks what would fit. THEN (important) went on Utube asking for video instructions. They had it on the computer and it was just too easy. What took the longest was the removable of the frozen food items and the drawers in the Bottom Freezer sect ... Read more ion.
Perfect product, perfect instructions, perfect job and worked perfectly!

Fridge only 18 months old too!

Handyman wanted $457.00 to do the job! HA.

The old switch was a little hard to get out....took me a couple tries. I couldn’t move the frig out to unplug it, so just shut the power off in the kitchen. But, I was happy that’s what the problem was and so happy to have the light back on......it was probably three years it didn’t work!

Unplugged the refrigerator. Used small flat head screw driver to push the front tab of the old switch in and pulled it out with pliers. Detached and reattached the wires to the switch. Reinserted back into hole. Plugged refrigerator back in to power. All good.

Unplugged the refrigerator, Taped around the edges of switch as I had read to prevent possible scratches, used very thin flathead screwdriver to pry out old switch, unplugged old switch, plugged in new switch, put it back in opening, plugged fridge back in, and I had beautiful light! Hardest part was unplugging the refrigerator!

pried out old switch, disconnected wires ,placed wires on new switch