Opening the refrigerator door releases this push-button switch to turn on the interior light, making stored food easier to see. When the door closes, it presses the button and turns the light off. A stuck, worn, or broken switch may leave the light off when the door is open or keep it on after closing. Replacing a faulty switch helps rest...Read moreore normal lighting control and reliable response to door movement. Disconnect the refrigerator from power before removing or installing the switch. This is an OEM part sourced directly from the manufacturer.
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
Controlled door travel helps prevent a refrigerator door from swinging beyond its intended opening range. This white plastic door stopper mounts near the bottom of the door and provides a stopping point as it opens. A cracked, worn, or broken stopper may allow excessive movement or fail to stop the door normally. Replacing a damaged stopp...Read moreer helps restore the intended swing limit and reduces strain caused by overextension. The stopper works with the hinge assembly to provide a mechanical limit during everyday opening and closing. This is an OEM part sourced directly from the manufacturer.
This deli drawer is for refrigerators. Deli drawer holds meats, vegetables and snacks in the fresh food compartment of the refrigerator. Follow the instructions in the owner's manual when installing this part.
Everyday drinks and condiments stay organized in this refrigerator door shelf bin. Its white plastic frame supports jars and bottles, while the clear front makes contents easy to see. The bin attaches to slots inside the door, adding storage without taking up room on the main shelves. A cracked base, broken mounting tabs, or damaged front...Read more panel may leave containers poorly supported. Replacing a worn or broken bin restores useful storage and helps keep items secure as the door opens and closes. This is an OEM part sourced directly from the manufacturer.
Proper movement of the center door flap helps a French door refrigerator seal the gap between its doors. This mullion spring applies tension to the hinged flap, guiding it as the door opens and closes. A broken, stretched, or missing spring may leave the flap loose or prevent it from moving into place, making door closure difficult. Repla...Read morecing a damaged spring helps restore controlled flap movement and proper sealing. Its coiled design stores and releases force as the mullion pivots during everyday use. This is an OEM part sourced directly from the manufacturer.
This ice maker assembly is for refrigerators. This Ice maker assembly contains the complete ice maker and housing. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
This is a genuine OEM evaporator motor that directly powers the evaporator mechanism within your refrigerator. This mechanism is responsible for pulling air over the evaporator coils, which are cold, and circulating that cold air back throughout the appliance. Without this motor, the interior of your refrigerator would build up frost, str...Read moreain the compressor, and simply not cool your fridge enough. A warm fridge, frost buildup or unusual noises are all signs that this fan needs replacing, and over time or through excessive dust building up, motor issues will arise and can cause it to fail. This fan motor is sold as an individual part, so it does not come with any securing screws or the fan blade itself. Replacing the evaporator fan motor will require your user manual and Philips-head and flathead screwdrivers. You need to gain access to the evaporator cover, which you will need to locate using your user manual schematics. Once the cover is removed and you disconnect the wire harnesses within it, you can disassemble the fan mechanism on its inside portion. With the fan mechanism disassembled, remove the old mechanism and install the new one, with the securing screws and wire harnesses.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Remove and replace light switch
45 of 91 peoplefound this instruction helpful.
Debbie from Waltham, MA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this helpful?
Thank you for voting!
Spring on door closer broke
11 of 17 peoplefound this instruction helpful.
Charles R from FAIRFAX, VA
Really Easy
Less than 15 mins
Pliers
Found the broken spring; matched it with parts diagram. Googled for sources via part number. Selected this site because it had best deal - price, availability, shipping. Part arrived as predicted; installed it in 2 minutes. Job done. Door now works.
Was this helpful?
Thank you for voting!
needed to replace broken ice maker
11 of 18 peoplefound this instruction helpful.
John from WEST ROCKPORT, ME
Very Easy
Less than 15 mins
Screw drivers
Take out 2 screws and unplug unit before removing. Plug-in new unit and screw in 2 screws. That's it.