7061288 Snapper Lawn Tractor Accessories - Overview

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

BOLT, 5/16-18 x 3/4" Short Neck Carriage, GR 5

It is a genuine item that is supplied by the original equipment manufacturer for use with Snapper riding lawn mowers and garden tractors. The purpose of this gage wheel is to support the deck allowing for easy transportation. It provides an identical replacement for a missing or a faulty component that was installed on a new unit. This hi...Read moregh-quality wheel is made of durable rubber and is sold individually, keep in mind the hardware to secure it is sold separately. Please make sure to check the diagrams of your model for the correct location and application of this part.

This is an authentic Murray replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The metal washer is used to provide spacing between the steering spindle and the front axle assembly. This item is sold individually, please note two washers may be needed.

This flange nut is designed for use in lawn and garden equipment. It is an OEM replacement part with a diameter of 0.375 inches and a thread pitch of 16 threads per inch. The nut has a ring-shaped extension on one end, known as a flange which helps to evenly distribute the clamping force of the nut and provide a more secure hold. Addition...Read moreally, the flange eliminates the need for separate washers and reduces the risk of abrasion on the surface being fastened. It is normal for the nut to corrode, crack, or for the threads to wear down over time. To replace the flange nut, unthread it from the fastener, and insert and secure the new one using a socket/wrench. Each sold individually.

This is an authentic replacement part, sourced from the original manufacturer for use with riding lawnmowers from Snapper and Murray. The durable plastic discharge chute connects to the side of the mower's deck and is used to guide grass clippings as they are discharged from the deck. This item is available as an individual replacement part.

This is an original Snapper replacement part manufactured for use with rear engine riding lawnmowers. The special aluminum spacer is used to secure the gage wheel. The spacer is hollow, and supports the bolt that goes through the wheel to secure it to the deck. The spacer is sold individually.

An authentic manufacturer sourced part which is supplied for use with Briggs and Stratton, Murray, and Snapper lawn and garden equipment. This replacement nut has a few different applications, please make sure to check the appropriate parts lists and diagrams of your model for the exact location of this hardware. Note, this durable metal nut is sold individually. You will need a wrench to secure or remove it.

This is a genuine manufacturer-approved component which is specially designed for use with Snapper lawn mowers. The purpose of this idler pulley is to apply tension to the belt. It is an identical replacement for a missing or a faulty part that was installed on a new unit. Please make sure to refer to the appropriate diagram of your model...Read more for the correct location and application of this component. Keep in mind this high-quality idler pulley is made of durable metal and is sold individually.

The bolt attaches to the pulley bearing. It is made of metal and is available individually. This part is an OEM from Snapper and Simplicity for use in lawn tractors and snowblowers. When replacing this item a wrench will be required during the installation process. It will require replacing if it becomes stripped or broken.

This is an original replacement part manufactured for use with Snapper riding lawnmowers. This special screw is commonly used to fasten the gage wheel to the front of the mower deck. The capscrew is available as an individual replacement part, please see model diagram for associative parts.

This is an original Snapper replacement part. The deck drive belt is designed by the manufacturer for use in lawn mowers. This part is made of flexible rubber, and is used in conjunction with the pulley assemblies to transfer power from the engine to the mower blade. You may require a wrench when replacing this item. This part is sold individually.