7060947 Snapper Lawn Tractor - Overview

This OEM hub cap keeps debris out of the hub and axle of your lawn mower. It is black in color, sold individually, and made of plastic. Over time, your hub cap may get removed or damaged due to fatigue and wear. If you notice it is missing or damaged, you will need to replace the hub cab. This is an easy repair that just requires the us...Read moree of a flat blade screwedriver for removal, and a rubber mallet for installing the new one inside the wheel hub.

The hair pin is a silver, metal pin used to secure and lock parts in place. If broken, the part being secured will come loose and the pin should be replaced. This is an OEM part directly from the manufacturer. Most customers rated the replacement of the hair pin as an easy repair.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

This is an authentic item that is supplied by the original manufacturer for use with Snapper lawn and garden equipment. The spring is utilized to apply tension on the latch. Over time the part can wear out and stretch eventually requiring a replacement. Please note this high-quality metal extension spring is sold individually. You may nee...Read mored pliers to perform this repair. Refer to the appropriate diagrams for your model when replacing this component.

The metal flat washer is priced individually. It attaches to the cast iron axle along with the bolt and the bearing. A set of pliers, a screwdriver, and a wrench may be necessary during the installation of this item. This is an original part for Murray lawn tractors and Snapper rear engine rider mowers.

This 5/16 washer, or toothed washer, is sold individually. It provides a tight fit between the knob and the upper handle on a range of outdoor power equipment. It attaches between the wing knob and the upper handle, and over time and through use, can become damaged and need replacing. It is gold in color and metal, and repairing it is an easy task according to our customers.

This part is priced as an individual replacement even though two may be needed. The flange ball bearing attaches to the front wheel, one on each side. It is made of metal and may require a set of pliers during replacement if this part breaks. This is a genuine Snapper replacement part that is sourced from the original manufacturer for use with rear engine rider mowers.

This is an authentic replacement part manufactured for use with rear engine mowers and lawn tractors from Craftsman. The user will need to replace this hex nut if it is missing or not working correctly. This hex nut screws onto the transmission link lever. This part is made of durable material and sold individually.

This hex center lock nut is sourced from the original manufacturer for use in lawn and garden power equipment. It is a hexagon-shaped fastener for bolts/studs that is responsible for the keeping the bolt/studs secure during use. The nut is made of metal and has a diameter of 5/16 of an inch and a thread pitch of 18 internal threads per in...Read morech. Over time the threads in the nut can wear down and the nut itself may crack or break. It is important to replace it as soon as necessary to avoid damaging your equipment. Use a socket or wrench to remove the old nut and thread the new one on. Make sure to order the correct number of nuts for your equipment as each nut is sold individually.

It is a genuine OEM sourced part that is specially produced for use with Murray and Snapper lawn and garden equipment. This is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. This high-quality carriage ...Read morebolt is made of durable metal and is sold individually, keep in mind the washer and other parts are all sold separately.

This is an authentic Snapper replacement part, sourced from the original manufacturer for use with riding lawnmowers. The plastic adapter is part of the grass bagging attachment and is used to connect the tube to the mower's deck assembly. This item is available as an individual replacement part.

The wing-nut is made out of metal and attaches to various other parts. It is a genuine OEM sourced part which is specially designed for use with lawn tractors made by Snapper and Simplicity. This part is available as an individual replacement even though several may be needed. It will need to be replaced if it becomes broken or stripped.