6911D Makita Impact Driver - Overview

This is a genuine Makita replacement part, it is sold individually. It is part of the bit holder. Without this Ball the bit would not stay in the holder. It is used in a number of different tools for different reasons. But it is most popular in Cordless Impact Drivers and Corded Screw Drivers. Compatible with the tools listed below. The diameter is 3.5mm.

This is an authentic OEM sourced part which is specially made for use with Makita power tools. It is an identical replacement for a missing or a faulty steel ball that was installed on a new unit. This is a standard hardware which may have multiple applications, please make sure to check the appropriate diagrams of your model for the corr...Read moreect location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

This is a genuine OEM sourced component which is specially designed for use with Makita power tools. It is an identical replacement for a missing or a faulty 7.2V-18V charger that was included with a new unit, please make sure to check the owners manual for the correct location and application of this part. Please note that a weak or defe...Read morective battery can damage the charger. Weak batteries are batteries with bad cells that will not hold a charge and keep charging eventually causing the charger to overheat and potentially smoke. Keep in mind this high-quality plastic body charger is sold individually.

This is a genuine OEM sourced replacement screw that is specially produced for Makita power tools. It has multiple uses depending on the tool, please make sure to check your equipments diagrams for correct location and applications of this hardware. One pan head screw with a washer is included per order.

This is a genuine manufacturer-sourced replacement switch which is specially designed for use with Makita power tools. Switches are a commonly replaced part which controls the on/off and variable speed functions, over time components may wear out and begin to fail eventually requiring a replacement. It is a high-quality part which is made of durable metal with plastic and is sold individually.

This o-ring is a genuine Makita replacement part, not imitation or overstock. O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: ...Read more • Extrusion and Nibbling - The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This genuine OEM steel ball measures 5.6mm in diameter and is used in the ball bearing mechanisms or detent systems of your handheld power tools. It minimizes friction between moving parts, allowing them to move smoothly without causing excessive wear or resistance. It can also provide a reliable locking mechanism in the detent system, en...Read moresuring that adjustable parts stay securely in place during operation. Typically, you can find this steel ball inside the main housing of your power tool. It facilitates smooth rolling or sliding movements in various components like compression springs, cam clutches, barrels, or spindles. Signs of a worn or damaged steel ball include increased vibration or inconsistent locking. To check if the steel ball requires replacement, visually inspect it for any signs of wear or damage. If you are unsure about how to replace the steel ball in your machine, it is recommended to consult your user manual for instructions. Please note that this replacement part is sold individually, as your tool may need multiple steel balls. It is also crucial to make sure you have the correct size of steel ball for your specific repair.