6905 - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This replacement clip is an authentic OEM component which is made for Makita impact wrenches. The part is secured in the anvil and it helps to apply tension on the socket to secure it. Over time it may wear out and lose tension eventually requiring a replacement. If a socket does not stay put on the anvil, a faulty or a damaged clip may b...Read moree the cause. Make sure to refer to the appropriate diagrams of your model for the exact location and the correct installation of this clip. One durable metal item is included. You will need pliers to remove the old one and secure the new one in the anvil.

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This authentic Makita replacement part is designed for use with impact wrenches. This pin fits in the anvil and it helps to hold sockets in place. This part is made out of metal and it is sold individually. To complete this repair you would need a screwdriver and pliers.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is an authentic replacement part manufactured for use with woodworking power tools. The hex socket head screw has multiple applications across a variety of tools. This socket head screw is sold individually, please see model diagram for part location and usage.

This ball bearing is assembled by the original manufacturer. It is used in a variety of Powermatic, Jet, and Wilton power tools. Ball bearings serve to protect moving parts from wearing each other down and from damage due to incorrect position/direction. This is a high-wear part and will need regular replacement. This part is sold individually.

This replacement switch is an authentic OEM sourced replacement part that is specially designed for Makita electric drills and impact wrenches. It is the part of the tool that allows user to turn the tool on and off. Since switches have moving mechanical parts, they will eventually begin to wear out and fail eventually requiring replaceme...Read morent. Please note this item is sold individually, to replace this switch you would need a screwdriver.

This genuine manufacturer-sourced part is specially designed for Makita power tools. It is an important component which provides a tight seal between connected components. Unfortunately, over time it will wear out and it may begin to crack eventually requiring a replacement. To ensure the correct repair procedure, refer to the appropriate...Read more diagrams for your model. Note, this high-quality insulation washer is made of durable material and is sold as an individual item. A screwdriver will be needed to take apart and reassemble the tool when performing this repair.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.