6904 - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This is a genuine item that is supplied directly from the original equipment manufacturer for use with Dynabrade sanders. The purpose of a muffler is to reduce noise that is coming from a working unit, but over time it may wear out and begin to fail eventually requiring a replacement. Keep in mind this high-quality component is made of du...Read morerable materials and is sold individually. Please make sure to check the appropriate diagrams of your model for the correct location and application of this part.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is an authentic replacement part manufactured for use with woodworking power tools. The hex socket head screw has multiple applications across a variety of tools. This socket head screw is sold individually, please see model diagram for part location and usage.

Genuine Dynabrade replacement part, this item is sold individually. The purpose of the 56027 Muffler is to lessen the noise of the air coming from the exhaust of the tools listed below. It will also filter out the excess oil that is in the tool. Once these Inserts get dirty and clogged they should be replaced.

This part is an OEM from Dynabrade. The speed regulator is made for use with many orbital sander devices. This item holds the valve stem in the housing assembly, and is sold individually. The plastic regulator manages the airflow, controlling the sander speed. You will need a pair of pliers for the installation.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

This is an authentic OEM sourced part which is specially made for use with Makita power tools. It is an identical replacement for a missing or a faulty steel ball that was installed on a new unit. This is a standard hardware which may have multiple applications, please make sure to check the appropriate diagrams of your model for the corr...Read moreect location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal co...Read morentact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.