6807 (Type 2) Makita Screwdriver - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

This set includes 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes...Read more can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

This authentic OEM part is compatible with various handheld power tools made by Makita including jig saws, routers, and sanders. A bearings main purpose is to decrease friction between moving parts. They also stabilize parts to keep proper direction and angle. Bearings are high wear items that may need regular replacement. Sold individually. Included in part number 517266-0 Armature Assembly 115V

This is a genuine Makita replacement part, it is sold individually. It is part of the bit holder. Without this Ball the bit would not stay in the holder. It is used in a number of different tools for different reasons. But it is most popular in Cordless Impact Drivers and Corded Screw Drivers. Compatible with the tools listed below. The diameter is 3.5mm.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

This genuine manufacturer-sourced part is specially designed for Makita power tools. It is an important component which provides a tight seal between connected components. Unfortunately, over time it will wear out and it may begin to crack eventually requiring a replacement. To ensure the correct repair procedure, refer to the appropriate...Read more diagrams for your model. Note, this high-quality insulation washer is made of durable material and is sold as an individual item. A screwdriver will be needed to take apart and reassemble the tool when performing this repair.

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal co...Read morentact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

It is a genuine OEM sourced item that is specially manufactured for use with Makita power tools. An o-ring is generally used to create a tight seal between two connected parts. Please note this replacement item has multiple uses depending on the model of your tool, make sure to refer to appropriate diagrams for correct application of this...Read more o-ring. Over time the material may deteriorate and crack, inspect the seals and o-rings periodically, and replace them as needed to maintain peak performance. This high quality rubber o-ring is sold individually.

This is an authentic OEM sourced part which is specially made for use with Makita power tools. It is an identical replacement for a missing or a faulty steel ball that was installed on a new unit. This is a standard hardware which may have multiple applications, please make sure to check the appropriate diagrams of your model for the corr...Read moreect location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.