This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
$46.04
In Stock
Order within the next 1 hr and 59 mins and your part ships today!
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
$7.71
In Stock
Order within the next 1 hr and 59 mins and your part ships today!
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
$33.12
In Stock
Order within the next 1 hr and 59 mins and your part ships today!
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$10.04
In Stock
Order within the next 1 hr and 59 mins and your part ships today!
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
$38.25
In Stock
Order within the next 1 hr and 59 mins and your part ships today!
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
$91.96
In Stock
Order within the next 1 hr and 59 mins and your part ships today!
Sold individually.
This dishrack adjuster is for dishwashers.
Dishrack adjuster lets you change the height of the dishwasher's upper rack.
Wear work gloves to protect your hands when installing this part.
$46.08
In Stock
Order within the next 1 hr and 59 mins and your part ships today!
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Order within the next 1 hr and 59 mins and your part ships today!
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$64.02
In Stock
Order within the next 1 hr and 59 mins and your part ships today!
This filter works with the water pump in your dishwasher. It prevents debris from entering the pump and causing damage. As a result, the filter can occasionally become clogged or damaged, and will nee...
$58.02
In Stock
Order within the next 1 hr and 59 mins and your part ships today!
Questions And Answers for 66513222N411
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Eric
January 10, 2020
I push start button comes on pots and pans heated dry but it doesn't start
For model number 66513222N411
Hello Eric, thank you for your question. We would recommend testing the following parts to determine the issue. Turbidity Sensor Part Number: WPW10705575, Door Latch - Black Part Number: WPW10653840, Thermostat Part Number: WPW10195091 and Overfill Control Switch Part Number: WPW10195039. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Kathy
August 10, 2023
My heating element went out - can I use a heating element for the model number 66513222N411? This is on my dishwasher. Thank you
For model number 66513222N411
Hello Kathy, thank you for your inquiry. Yes, you can replace the heating element, part number PS9494999. It is compatible with your model. We hope this information helps!
I can "power on " the dishwasher, and the display shows everything as normal, even so far as to give the countdown time for the cycle. However, nothing else actually runs. It's as though the control panel is doing its job, but the signal doesn't get to what it needs to activate. What should I check to trace this problem?
For model number 66513222N411
Hello Bob, thank you for contacting us. Based on the description that you have provided, we would recommend checking the user interface board, part number PS9864655, to fix the issue. Glad to be of assistance!
Hi Wanda, thank you for reaching out. We have found that your model comes with 2 seals. The dishwasher door seal is part number PS12348515, and the cabinet seal is part number PS11731683. We hope this information is useful!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water i
... Read morenput line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.