66-651 (Type-0) Delta Compressor - Overview

This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with air compressors. The three wire cord is encased in a durable jacket and includes terminals at the end of the wires. The cord is used to relay electricity from the outlet to the switch assembly. This item is available as an individual replacement part.

This wheel is a genuine OEM replacement part used in portable air compressors. It consists of a plastic rim and rubber tire with an outer diameter of 9.5 inches. It is held in place on the compressor axle by a shoulder bolt and nut. The wheel allows the equipment to move smoothly during use. If the tire is punctured, or the rim is damaged...Read more, the wheel will need to be replaced to restore the portability of your equipment. If the nut and bolt are worn down, it is recommended to replace them at the same time. Remove the nut and bolt that secure the wheel and pull it off the axle. Place the new wheel in position and secure it with the fasteners (sold separately). Each wheel is sold individually.

This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to secure the compressor shroud. It is recommended to refer to specific manual and diagrams for repair instructions. This part is sold individu...Read moreally. Purchasing spare screws is also encouraged, as they can wear out over time and regular use. A hex key and a screwdriver are helpful in the removal and replacement.

This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentially damaging the pump. A hex driver, or screwdriver may be needed to install this item and it is sold individually.

This is an authentic replacement part that has been OEM sourced to be used with Porter Cable, DeVilbiss, and Black and Decker air compressors. The metal nut is commonly used to connect the outlet tube to the cylinder head assembly. This item is available as an individual replacement part, a hex wrench is needed for this repair.

Used to secure the wheels on a compressor or generator, this Shoulder Bolt is roughly 3.75 inches long and is sourced directly from the original equipment manufacturer. It is made of dark grey metal, is not part of a kit or assembly, and is sold individually. This part needs to be replaced when it is damaged or worn and may cause the w...Read moreheel to fall off if it breaks. You will need a wrench or socket to complete this repair. Customers rate this repair as Easy.

This is an OEM part sourced directly from the manufacturer. The adapter is designed for use in compressors from DeVilbiss, Black & Decker, Delta, and Porter Cable. This part is made of metal, and may be used to connect the regulator to the tank. You will require a wrench when replacing this part. This item is sold individually.

This is an original Porter Cable replacement part. The isolator is designed by the manufacturer for use in air compressors. This part is made of pliable rubber, and is place on the base of the motor assembly to cushion and separate it from the tank assembly. No tools are required when replacing this item. Simply remove the old part and slot the new one into place. This part is sold individually.

This is an authentic manufacturer-sourced replacement o-ring which is specially designed for use with air compressors. It helps to provide an air tight seal for the nut which secures the outlet tube, please make sure to check appropriate diagrams of your model for correct location and use of this item. Over time o-rings tend to deteriorat...Read moree and crack eventually requiring replacement to maintain the proper seal. Note it is a high-quality component which is made of durable rubber material and it is sold individually.

This check valve is used to direct air from the cylinder to the tank, and to prevent air from going back into the pump. It is a genuine OEM part used on air compressors. It features threaded fittings to attach it to the tank, pump, and pressure switch. A faulty check valve can cause the pump to restart even with a full tank, that in turn ...Read morecan overload the motor. This brass part is sold individually, and the tubes are sold separately. Always make sure to drain the tank before beginning the repair.