6500G - Overview

This OEM replacement fuel gauge cap is designed for use in generators. It comes in a cylindrical shape and has a built-in window to easily view the fuel levels without pulling out the entire cap. It is approximately 5.25 inches in length, while the head has a diameter of 3 inches. The purpose of the cap is to cover and protect the fuel ga...Read moreuge, which indicates the levels of gas available in the tank. It prevents dirt and debris from entering the gauge area and prevents fuel from leaking out. A faulty cap will allow contaminants to enter the gauge, and cause fuel to leak, leading to inaccurate fuel readings and safety risks. Twist the cap to remove it and clean the surrounding area thoroughly. Place the new gauge cap in position and ensure that it is locked in place.

This high quality wheel and tire assembly is a genuine manufacturer sourced replacement part that is specially produced for Karcher pressure washers. It is the wheel that supports and helps to move your unit around. This part consists of a durable metal wheel with a rubber tire and it is sold individually, please note the hardware to secure it is sold separately.

This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The most common reasons for replacing the grommet is if the fuel is leaking from the fuel tank, the fuel lines are loose at the tank or the rubbe...Read morer grommet is cracked and not sealing. This part is made out of rubber and is sold individually. Here is a list of tools that are needed to replace the grommet a receptacle for draining fuel, a wire hook (to retrieve fuel lines), screwdriver, wire cutters or scissors.

O-rings are flexible circles which are used to prevent leaks and maintain pressure. This part is an authentic OEM replacement ring used in Karcher pressure washers. These O-rings are used at the connection point between the machine and its hose. This set includes five (5) identical O-rings. Please note that the wand itself uses a separat...Read moree set of O-rings, part # 2.640-729.0 O-Ring Seal Set. Multiple other sizes of O-ring are used in various other spots on these machines; see manual for part numbers and placements.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

This is a genuine item that is specially designed for use with Karcher pressure washers. It is supplied by the original equipment manufacturer. The oil helps to lubricate internal components of the pump to ensure it runs properly. Check the oil level regularly. Oil level should always be between the "FULL" and "ADD" level marks on the dip...Read morestick. Be sure the machine is level when checking the oil level. This will prevent them from wearing out. Refer to the owners manual of your model for the correct application of this oil. This synthetic 15W40 oil is sold in a single 1-liter container.

This is an authentic Karcher replacement part manufactured for use with pressure washers. The spacer is used as an isolator to reduce vibration from the engine. This spacer fits between the engine and the frame, please note the spacer is sold as an individual replacement part.

This is an authentic OEM sourced part which is specially made for DeWALT planers. It functions as a safety device. When the circuit becomes overloaded, this circuit breaker switch interrupts the transfer of electricity to the motor. Flip the switch on the circuit breaker to reset the connection. Please make sure to refer to the appropriat...Read moree diagrams for your model for the correct location and application of this component. Keep in mind this high-quality circuit breaker is sold as an individual item.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

This is an authentic Karcher replacement part that has been sourced from the original manufacturer to be used with pressure washers. The metal cap is used to cover the end of the axle that the wheel mounts to. This cap is available as an individual replacement part.

This is a genuine OEM supplied part that is specially designed for Briggs and Stratton portable generators. The item provides an identical replacement for a faulty or a missing power regulator assembly that was installed on a new unit. It is made of high-quality materials and is sold as an individual item. Refer to the owner's manual and the appropriate diagrams for your model to ensure the correct repair procedure.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton generators and pressure washers. The purpose of this component is to reduce the vibration of a working unit, unfortunately, over time it may begin to fail eventually requiring a replacement. Please make sure to refer to...Read more the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality vibe mount with a washer is sold individually.