Models > 62946965

62946965 Kenmore Range - Overview

Sections of the 62946965

[Viewing 9 of 9]
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W – Part Number: 8009
Light Bulb - 40W
★★★★★
★★★★★
(63)
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$7.32
  In Stock
Grease Filter – Part Number: WP71002111
Grease Filter
★★★★★
★★★★★
(38)
PartSelect #: PS11743870
Manufacturer #: WP71002111
This filter is made of metal and is intended for use with ranges and cooktops. Grease filters are an important but often neglected part of ranges. If the filter is full, your extractor fan will become...
$30.36
  In Stock
Screw – Part Number: W11233072
Screw
★★★★★
★★★★★
(6)
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$19.99
  In Stock
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.76
  In Stock
Surface Burner Switch - 240V – Part Number: W11120791
Surface Burner Switch - 240V
★★★★★
★★★★★
(10)
PartSelect #: PS12347301
Manufacturer #: W11120791
$74.76
  On Order
Toggle Switch - With Push Nuts – Part Number: 12200039
Toggle Switch - With Push Nuts
PartSelect #: PS2005745
Manufacturer #: 12200039
This toggle switch is also known as a fan switch. It has three positions: low, off, and high. This switch allows you to select the speed for the fan.   No Longer Available
Screw – Part Number: WP179051
Screw
★★★★★
★★★★★
(5)
PartSelect #: PS11738704
Manufacturer #: WP179051
Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an appliance to ensure ...
$7.76
  In Stock
2 Piece Broiler Pan – Part Number: 4396923
2 Piece Broiler Pan
★★★★★
★★★★★
(4)
PartSelect #: PS971245
Manufacturer #: 4396923
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set ...
$39.67
  In Stock
Single Grill Grate - Black – Part Number: 7518P054-60
Single Grill Grate - Black
PartSelect #: PS3417872
Manufacturer #: 7518P054-60
Sold individually.   No Longer Available
Rock Grate Support – Part Number: 700819
Rock Grate Support
PartSelect #: PS1640535
Manufacturer #: 700819
Sold individually.
$41.85
  In Stock
Cartridge Male Contact Spade – Part Number: Y708572
Cartridge Male Contact Spade
★★★★★
★★★★★
(1)
PartSelect #: PS1988157
Manufacturer #: Y708572
This cartridge assembly male contact spade is made of metal. These are sold individually, though each range uses four contact spades.
$10.61
  In Stock
Oven Rack – Part Number: Y704660
Oven Rack
★★★★★
★★★★★
(2)
PartSelect #: PS2201584
Manufacturer #: Y704660
Sold individually.
$72.43
  In Stock

Questions And Answers for 62946965

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the 62946965

[Viewing 7 of 7]
Element will not heat
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
Show All
Oven not heating evenly
Fixed by
these parts
Show All
Little to no heat when baking
Fixed by
these parts
Show All
Touchpad does not respond
Fixed by
these parts
Show All
Oven is too hot
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace Grease Filter
Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.
Parts Used:
Grease Filter
  • Gene from Washington C.H., OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
523 of 531 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blower motor died and I needed to replace it
Most of the repair was obvious as I took the blower apart before ordering the parts. Unfortunately the new motor was significantly larger than the original motor so I had to um. Adjust the position of some of the other parts to fit it in. There was a sheet metal flange that was installed on the other side of the blower from the motor which was designed to focus the air flow into the blower. I used a hammer to ajust the angle of flange so it no longer extended as far into the blower housing.

It works just fine although its a bit louder than the old motor was.
Parts Used:
Hose Clamp Motor Isolator Grease Filter Urethan Foam Gasket Blower Motor Kit
  • John from Berkley, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
374 of 381 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner had one temperature--hot, regardless of setting
1. Killed power and removed the regulator's knob, noted the position of the old control.
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.

(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)

Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).
Parts Used:
Surface Burner Switch - 240V
  • James H from Oxford, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
98 of 110 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!