My Orders
6228369301NZ Kenmore Trash Compactor - Overview
Diagrams for 6228369301NZ
See every part. Know exactly what you need.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$77.75
In Stock
Drive Gear Kit
Part #882699
This is the drive gear kit for the ram that compacts the trash inside your compactor. If your compactor ram is getting stuck, there is excess noise during its cycle, or if your compactor does not stop at the end of its cycle, the driving gear may be the issue. The gear is white, plastic and approximately 4.5 inches in diameter. This drive...Read more gear kit includes both gears, pin spring, retaining clip (c-ring), ram stop, ram cam, and instructions. Make sure to disconnect the power to your trash compactor before beginning the repair.
Read less
$7.47
In Stock
$6.40
In Stock
Washer Front Leveling Foot
Part #WPW10001130
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause...Read more it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.
Read less
$40.02
On Order
15" Compactor Bag Carrier with Easy Grip Handles
Part #13030RP
This 15 inch compactor bag carrier fits around the compactor bag inside the compactor and is used to easily lift and remove trash compactor bags once they are full. Simply place the reusable bag carrier in the garbage can before placing a new compactor bag in the bin. The easy-grip handles make removal easier once the bag is full. This pi...Read moreece also makes a good carrier for bringing in logs for your fireplace. This part fits most 15 inch compactors. For the full list of compatible compactors, check the list below. Compactor bags are sold separately.
Read less
$57.38
In Stock
Trash Compactor Directional Switch
Part #WP777811
Here's a reliable solution when you need to get your microwave working as good as new - the GE Advantium Metal Tray. At the heart of your microwave, this tray works tirelessly to rotate your food, delivering evenly cooked meals every time. The tray is non-stick, making your cleaning process a breeze. The tray is incredibly easy to fit in...Read moreto your microwave. Just follow the simple instructions in the owner's manual, and you'll have it set up in no time. The best part? It?s designed to perfectly enhance the performance of your microwave, enriching your cooking experience from start to finish. Let this tray be the trusted ally for your microwave, brought to you by GE - a brand that's renowned for its long-lasting and high-quality home appliances. Remember, the right replacement part can make your appliance work like new again. This tray not only solves the problem of uneven heating but also ensures smooth functionality of your microwave over the years. So bring home the GE Advantium Metal Tray, and watch your microwave transform your kitchen and meal times.
Read less
$97.57
In Stock
Rotary Switch Kit
Part #675382
The rotary switch kit is also known as the start switch or the on and off switch, and is used to power on your trash compactor. The function of the rotary switch kit is to control the electrical power that is going into your trash compactor. This process happens when the switch sendsvoltage to the motor to start the compacting cycle. If y...Read moreour switch is broken the trash compactor will not start. A multimeter test can be performed to test the switch for continuity. The rotary switch kit will come with an on and off rotary switch, and two chrome knobs.
Read less
$47.40
Special Order
Power Nut
Part #WP777533
This part is a power nut, and it is intended to be used in conjunction with trash compactors. The function of this nut is to fasten to the side of the ram where it is threaded. When the power screw rotates, it is fed through the power nut, which pulls the ram down to compress the trash. This part is just over an inch in diameter, and is j...Read moreust one inch thick. This part is white and made entirely of plastic. The reason for needing to replace this part is if your compactor ram gets stuck, or if it does not stop at the end of the compacting cycle.
Read less
$17.15
In Stock
Drawer Roller
Part #WP9871602
This bearing roller may also be known as the wheel assembly or the container roller bearing, and it is a piece for your trash bin. The function of this bearing is to work in conjunction with your trash bin to allow the canister to roll free. For this repair you will need a nut driver, a pair of pliers, a screwdriver set, and an adjustable...Read more wrench. The most obvious symptom that will require you to replace this part is if your drawer is hard to open and/or close. Your appliance comes with two bearing rollers and it is sold individually.
Read less
$70.95
In Stock
Foot Pedal
Part #882657
This replacement part is a foot pedal which fits on a trash compactor. It includes two screws for installation. The pedal mounts on the footplate on the bottom front of the container. The pedal controls the container drawer. When stepping on your trash compactor pedal, the latch should release the container from the compactor body. This f...Read moreoot pedal is black, made of plastic, and is sold individually. Be sure to disconnect power to your appliance before beginning this repair. You will only need a screwdriver to complete the repair. This is a genuine part and is sourced from the authentic manufacturer.
Read less
$27.36
In Stock
Wheel Assembly - Kit of 2
Part #882688
This wheel assembly, or roller assembly, is for a trash compactor. The kit includes two wheels that are approximately 1 inch in diameter each. The wheels allow the trash compactor container to roll in and out of the appliance. You may have to replace the wheel assembly if the container does not roll smoothly. To access the existing wheel ...Read morekit on your appliance, uninstall appliance from the cabinet, depress foot petal to lift the container off its track, and remove the container from the tracks. This kit is an OEM part sourced from the authentic manufacturer factory.
Read less
$20.37
On Order
Key
Part #776594
This replacement knob and safety key is designed for trash compactors, providing both convenient operation and added protection. It functions as the start control, allowing you to easily activate the compactor, while also serving as a built-in safety feature—removing the key disables the unit to help prevent unintended use. Durable and ea...Read moresy to install, it’s an ideal solution for replacing worn, damaged, or missing knobs, helping restore safe and reliable everyday operation.
Read less
$105.46
On Order
Common Symptoms of the 6228369301NZ
How this model fails, and the parts that fix it.
Doesn’t stop at end of compacting cycle
Fixed by
these parts
these parts
Show All
Compactor ram gets stuck
Fixed by
these parts
these parts
Show All
Drawer is hard to open and or close
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Won’t start
Fixed by
these parts
these parts
Show All
Won’t stay on
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Change out defective switch
37 of 50 people
found this instruction helpful.
Pulled out compactor drawer and removed same, slid the compactor cabinet out and unpluged the appliance. Removed the two phillips head screws to release the control panel. lossened the locking nut from switch. matched the switches to be sure parts were the same,switched the wires to the new switch and reinstalled.replaced phillips screws,
... Read more
all Done !!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!