622594X85NB (2005) Briggs and Stratton Snow Blower - Overview

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

This is an OEM replacement part for Briggs and Stratton, Murray, Snapper, and Simplicity engines. When engaged the ignition key starts the lawn tractor. This part is made of metal and is sold in a set of two. There are no tools needs to use this part, as it comes pre-assembled and really to use.

This is a genuine manufacturer-approved item that is specially designed for Craftsman snowblowers. It is an identical replacement for a missing or damaged knob that was originally installed on a new unit. The purpose of this component is to provide a user with a comfortable grip to secure the adjusting chute. Please make sure to refer to ...Read morethe appropriate diagrams of your model for the exact location and the correct installation of this component. Keep in mind this durable plastic knob is sold individually.

This authentic replacement part is designed for use with Murray, Simplicity and Snapper snowblowers. Flange bearings are used to provide support for a shaft while reducing friction between rotating parts. The rollers take the load and spin, distributing the weight evenly while the minimal contact area of the roller reduces friction. Beari...Read morengs experience constant wear from pressure, heat, vibration, and friction. Because of this, many bearings need to be periodically replaced. Make sure to check the diagrams of your model for the exact location and the correct installation of this component. It is sold individually. You will need a screwdriver and a wrench set to take apart the housing in order to gain access to this flange bearing. Keep in mind the screws utilized to secure this component are sold separately.

This OEM universal joint pin is used within various models of snowblowers to hold the rod and yoke together inside the deflector/chute assembly. If you notice excessive vibrations, clunking, or limited range of motion within the chute mechanism, it is worth inspecting to check for a broken pin or other internal damage. To prevent any futu...Read morere issues with your universal joint pin, make sure to keep it adequately clean and lubricated and inspected regularly. This pin is made of a high-quality metal, measures 1-inch long and .375-inches thick, and is sold as an individual part.

A genuine item which is supplied directly from the original equipment manufacturer for use with Murray and Snapper lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check the appropriate diagrams for the correct location and use of this screw. Keep...Read more in mind this high-quality component is made of durable metal and is sold individually.

This is a genuine Murray, Snapper, and Simplicity part sourced directly from the manufacturer for use in snowthrowers. The clutch spring boot is made out of rubber. A set of pliers may be necessary during the installation of this item. It may become broken and will need to be replaced. This is available as an individual replacement part.

This is a genuine replacement part manufactured for use with outdoor power equipment. The special nut is used with a variety of types of equipment and the application of the nut varies depending on the model of equipment. This nut is available as an individual replacement part, please see model diagram for the nut\'s location and usage.

This is a genuine OEM sourced part which is designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It provides an identical replacement for a damaged or a missing component that was on a new unit. By pressing on the purge bulb, it will force fuel into the fuel line from the fuel tank into the ca...Read morerburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in the fuel return line. At some time the primer will lose its elasticity or crack and need to be replaced. It is made of high-quality rubber material and is sold individually. Keep in mind the #696824 Nut (Carburetor Primer) that helps to secure it is sold separately. Replacing the primer is a simple task, simply remove the old one and connect the new one to the hose.

This is a genuine part which is supplied directly by the original equipment manufacturer and is used with Murray, Snapper, and Simplicity snow throwers. The scraper blade attaches to the bottom of the auger housing, to protect the housing and augers from ice and other debris. This part is made of durable plastic and is sold individually. ...Read moreBefore installation, be sure to remove the ignition key. You will need a socket wrench to aid you in this repair.