EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

6150 - Overview

Models starting with 6150

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Clutch-starter – Part Number: 399671
$48.09
In Stock
Clutch-starter
★★★★★
★★★★★
(2)
Part #399671
This starter clutch is an authentic OEM replacement part used in small outdoor power engines. Each package includes one clutch and one ball bearing. The starter clutch allows the engine to start by engaging the crankshaft to spin the engine and initiate combustion. Once the engine starts the clutch disengages to prevent over spinning. Over time the clutch may fail due to worn-down bearings, or damage to the clutch body, resulting in hard starting or failure to start. To replace it, first, disconnect the spark plug for safety. Then, remove the engine cover to access the starter clutch. Remove the clutch from the crankshaft, and thoroughly clean the mounting shaft. Install the new clutch by screwing it onto the crankshaft, then reassemble the engine cover and reconnect the spark plug.
Seal-oil – Part Number: 299819S
$7.47
In Stock
Seal-oil
Part #299819S
This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to your make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.
Gasket-intake – Part Number: 27355S
$6.40
In Stock
Gasket-intake
Part #27355S
This is an authentic manufacturer sourced replacement part designed for use with a variety of lawn and garden equipment. This carburetor intake gasket which provides an air tight seal for the carburetor. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.
Gasket-breather – Part Number: 27549S
$6.40
In Stock
Gasket-breather
Part #27549S
The Breather Gasket is OEM and used to provide an airtight seal for the breather assembly. It is a gray part, attached between the breather cap and engine. Installation is rated "Easy" and will require a wrench set and socket set. If broken, damaged, or worn due to fatigue, there may be oil leaking from it, and the engine may be running rough from an unwanted vacuum sucking in air. If this happens, replace the part. Refer to your make, model and diagrams to ensure this is the correct part for you.
Engine Oil Filter – Part Number: 1205001-S
$17.76
In Stock
Engine Oil Filter
Part #1205001-S
This genuine OEM oil filter helps to remove harmful contaminants from engine oil. It is designed for a variety of Engines. It is sold Individually. This part maintains optimum performance of your engine in accordance with applicable EPA emissions regulations. It is recommended to replace an Oil Filter at least once a season.
Rod: Push – Part Number: 2441105-S
$8.60
In Stock
Rod: Push
Part #2441105-S
This replacement push rod is specially designed for Kohler engines commonly installed on a variety of lawn and garden equipment. It is an authentic high-quality item that is sourced from the original equipment manufacturer. The rod is attached to the camshaft to push the exhaust valve open during the exhaust stroke. A bent pushrod can not only affect your engine\\\'s performance, but it can also seriously damage other parts if the problem is not taken care of immediately. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. It is made of durable metal and is sold individually. You will need a screwdriver and a wrench set to take the engine apart in order to perform this repair.
Screw – Part Number: 691640
$8.33
In Stock
Screw
Part #691640
This is a genuine OEM sourced part which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.
Filter-a/c Foam – Part Number: 27987S
No Longer Available
Filter-a/c Foam
Part #27987S
This air cleaner element is supplied from original manufacturer. It is specially designed for use with Briggs and Stratton engines used on lawn and garden equipment. It is used to filter out dust from entering the carburetor and the engine. This filter element is made out of foam material and it is sold individually. Please note, the air cleaner cartridge is sold separately. Replacing this filter is a simple task that does not require any tools. • Unscrew the cover knob • Remove the cover • Remove old element • Secure the new element in place • Reassemble and test the unit
Seal, Oil (pto End) – Part Number: 2503206-S
No Longer Available
Seal, Oil (pto End)
Part #2503206-S
This oil seal is a genuine OEM replacement part designed for lawn and garden equipment. It is a small, circular rubber seal with a diameter of 2 3/8 inches, used to prevent oil leakage between the gear cover and gear shaft, and prevent the entry of contaminants. You will need to replace this oil seal if it is brittle, cracked, or has lost elasticity. A faulty seal will cause the gears to lose lubrication, increase friction damage, and prematurely wear down the parts. Remember to drain the oil from your equipment before beginning any repairs. Carefully pry the old seal from its mounting position and clear off any debris and residue on the area. Place the new seal in position and ensure it is securely fitted.
Armature-magneto – Part Number: 591420
$62.60
In Stock
Armature-magneto
★★★★★
★★★★★
(1)
Part #591420
This replacement armature-magneto is specially designed for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is an authentic part sourced directly from original equipment manufacturer. The armature-magneto also known as an ignition module produces pulses of high voltage for the spark plugs. This item includes (1) armature-magneto and (1) lead wire per order. To complete this repair you will need screwdriver set.
Screw: Flg M10x1.5x90 – Part Number: 6208608-S
$9.42
In Stock
Screw: Flg M10x1.5x90
Part #6208608-S
This is a genuine Kohler replacement part that has been sourced from the original manufacturer to be used with small engines. The metal screw is used to secure the head to the top of the cylinder assembly. This screw requires a hex ratchet set to install and is priced as a single item.
Key: 3/16 X 5/8 – Part Number: X-42-15-S
$6.40
In Stock
Key: 3/16 X 5/8
Part #X-42-15-S
This OEM part is sold individually and is a direct replacement part sourced from the manufacturer. The Woodruff Key is used to allow mating parts such as a shaft and gear to rotate together. It is made of silver-colored metal and is found in various locations, depending on your model. This part will wear over time and needs to be replaced when damaged, worn, or if the mating parts no longer rotate together. Customers rate this repair as Easy.

Exact Part matches for your search term

USE PRO TJ6150 – Part Number: 6150
No Longer Available
USE PRO TJ6150
This part number matches the current model number 6150
Part #6150
Shield-Ram – Part Number: 6150
No Longer Available
Shield-Ram
This part number matches the current model number 6150
Part #6150
CASTER WITHOUT BRAKE – Part Number: 6150
$48.51
Special Order
CASTER WITHOUT BRAKE
This part number matches the current model number 6150
Part #6150
3250 WATT PORTABLE CALIFORNIA – Part Number: 6150
$893.88
Special Order
3250 WATT PORTABLE CALIFORNIA
This part number matches the current model number 6150
Part #6150
WELD BUTTON – Part Number: JT9-6150
$52.61
Special Order
WELD BUTTON
This part number matches the current model number 6150
Part #JT9-6150
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Could not keep an aftermarket muffler on the engine.
15 of 20 people found this instruction helpful.
  • Richard from KERNERSVILLE, NC
  • Really Easy
  • 15 - 30 mins
  • Wrench set
Once I determined what OEM muffler I needed, installation was relatively easy. I have a 1982 4hp Briggs on my Snapper tiller. There was a 90* galvanized elbow coming out of the exhaust port, with a bezel nut to lock it down. Do not remove the elbow, even though it appears that you should. If you install the muffler without the elbow the m uffler will parallel the the vacuum for the carburetor and can melt the rubber couplers. Use the elbow to direct the heat away from the carburetor. Use a pipe wrench to lock down the bezel nut because the weight of the muffler, especially under vibration, can work loose and fall down on the tine belt cover and melt it. The bezel nut that comes with the muffler should also be used to lock down the muffler to the threaded intake bracket that comes with the muffler, not to replace the bezel nut for the elbow.
Was this helpful?
Thank you for voting!
Push mower leaked under neath.
1 person found this instruction helpful.
  • Raymond from Coalport, PA
  • Easy
  • 15 - 30 mins
  • Pliers, Socket set
Pulled the old seal out, replaced it with seal #391483S and so far looking good !
Was this helpful?
Thank you for voting!