The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, or you notice that your dishwasher is not cleaning dishes properly, you may need to replace the rack wheel. The single rack roller kit is mad...Read moree of white plastic, and clips to the dishwasher rack with the included axle/clip. Many of our customers have described this repair as easy, and you will not require any tools to complete it.
Lower rack roller and bracket assembly, grey. Wheel has been updated. If wheel pictured is not like old one, you may need to replace all wheels.
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing water leaking out. If broken, it should be replaced. Refer to your model number and user manual to ensure this part is right for you. When makin...Read moreg this repair, open the dishwasher door and take out the lower dish tray for better access. Pull out the old gasket, and clean the channel with a rag. Push the new gasket into place into the notch on the door, which you should see upon close inspection, using a flat-head screwdriver for assistance if necessary. We do not recommend cutting any additional length off on the tub gasket if any is present during your repair.
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step gu...Read moreide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spray arm and is found at the bottom of the dishwasher. The lower spray arm spins on the support when the dishwasher is running. If the support ...Read moreis cracked or broken, the spray arm may not spin, and your dishes will not be cleaned properly. You may also notice that your dishwasher is noisy when it runs; this can mean the arm support is damaged as well.
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, dependin...Read moreg on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.
This door spring is manufactured for a dishwasher door. The door spring applies tension to the dishwasher door so that the door does not drop too quickly when it is opening. If the door drops too quickly, it could cause damage to the dishwasher door or dishwasher door hinges. This spring is sold individually. Check the spring on the oppos...Read moreite side of the dishwasher door, they often wear at the same rate so you may want to replace both springs for exact tension on either side. No tools are required for this repair. This is an OEM replacement part.
Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to op...Read moreerate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.
This dishwasher heating element is a genuine replacement component designed to maintain optimal water temperature during the wash cycle and assist in drying dishes at the end of the cycle. Positioned at the bottom of the dishwasher tub, it ensures efficient cleaning and drying performance. Compatible with a wide range of models from Frigi...Read moredaire, Kenmore, Crosley, Electrolux, and other related brands, this element replaces older versions and restores proper function when symptoms such as poor cleaning, inadequate drying, or water leaks occur. Installation requires disconnecting power to the appliance to ensure safety. Sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower Rack Roller Missing
379 of 395 peoplefound this instruction helpful.
Sandra from Mount Vernon, WA
Really Easy
Less than 15 mins
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.
Was this helpful?
Thank you for voting!
dishwasher was leaking water
177 of 213 peoplefound this instruction helpful.
Charles from Milton, FL
Really Easy
Less than 15 mins
Screw drivers
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
Was this helpful?
Thank you for voting!
Cord was not tightened enough by delivery crew.
109 of 174 peoplefound this instruction helpful.
Timothy from Spring Valley, AL
Really Easy
15 - 30 mins
Screw drivers, Socket set
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede
... Read mored are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.