6010BVR Makita Drill - Overview

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal co...Read morentact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This 5 x 8 carbon brush holder is a genuine OEM replacement part used in various outdoor power equipment. It is a small plastic box with a cavity, and it is located near the engine assembly. The brush holder is responsible for holding and making electrical contact with the carbon brushes. The carbon brushes provide electrical current to t...Read morehe moving parts of the equipment. A faulty carbon brush holder will lead to reduced power output or complete loss of power. You will notice difficulties starting the engine, and the equipment may shut off during use. To begin the repair, first disconnect the power source. Remove the motor housing cover to access the holder and release the old brushes. Attach the new holder in place and reinsert the carbon brushes. Reassemble your equipment and switch it back on to check for functionality. Each brush holder is sold individually.

This rubber piece is a genuine Makita manufactured part. It is manufactured for various power tools. A cord protector guards the wires from damage caused by motion and strain. Damaged cords must be replaced to avoid safety hazards. A replacement cord is sold separately. This item consists of one (1) cord protector. This is a simple and qu...Read moreick repair. • Unplug machine • Remove the casing • Detach cord from tool • Slide cord protector onto cord • Reattach wires and casing • Test power tool

This is a genuine OEM sourced replacement part which is specially designed for use with Makita power tools. The purpose of this strain relief is to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard. Keep in mind it is made of durable rubber and is sold individually.

This authentic OEM sourced part which is specially made for use with Makita power tools. It is important to have a cord protector on your tool to improve friction, seal cable and protect it from a potential damage. The part provides an identical replacement for a missing or a faulty component that was installed on a new unit. Please make ...Read moresure to refer to the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality strain relief is made of durable rubber and is sold individually.

This is an OEM part sourced directly from the manufacturer. The pan head screw is designed for use in Makita power tools such as sanders and miter saws. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws used in the machine. Refer to the...Read more parts diagram to be sure of ordering the correct part. You will require a screwdriver when replacing this part. This item is sold individually.

This pan head screw is a genuine replacement hardware sourced directly from original equipment manufacturer. It is specially produced for use with a variety of power tools. Please make sure to check appropriate diagrams for your tool to ensure the correct location and applications of this hardware. Includes one (1) metal screw and a washer.

This is an authentic replacement part manufactured for use with Makita power tools. The sealed ball bearing is commonly used to reduce friction between a rotating shaft and a fixed part assembly. This ball bearing is available as an individual replacement part, please see model diagram for associative parts.

This is a genuine Makita replacement part. The pan head screw is designed by the manufacturer for use in drills and hammer drills. This part is made of metal, and is generally used to secure the drill chuck. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the corre...Read morect part. You will require a screwdriver when replacing this item. This part is sold individually.