This water filter (Whirlpool EveryDrop Refrigerator Water Filter, Single Turn Filter) purifies water going to the water dispenser and sometimes the icemaker as well. This part should be replaced if it is causing reduced water flow or just replaced periodically per the owner manual. Replacing this water filter may fix a noisy or leaking fr...Read moreidge, a fridge that is not dispensing water (or reduced flow rate), and an ice maker that is not making ice at all, or not making enough ice. This filter is white, sold individually and measures 8 inches by 3 inches in diameter. This water filter has been updated by the manufacturer. It may appear different but will still function the same. It is sold individually.
If your refrigerators interior light is not working, the door switch may be the cause. It turns the light off when the door closes. This is an OEM part. Confirm compatibility using your refrigerators model number.
The refrigerator light and fan circuit uses this three-terminal rocker arm switch. It is an OEM replacement part. Disconnect power before working on this electrical part.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
Carry defrost water away from the freezer with this refrigerator drain tube kit. It directs melted frost into the drain pan beneath the appliance, where the water can evaporate. The updated curved tube replaces older drain designs that can clog and cause water to back up. A blocked or damaged drain may lead to ice on the freezer floor or ...Read morewater leaking beneath the refrigerator. Installing the kit helps restore proper drainage. Unplug the refrigerator before accessing the lower rear compartment. This is an OEM part sourced directly from the manufacturer.
Water can still flow to the refrigerator dispenser and ice maker with the filter removed when this OEM bypass plug is attached in the water filter head. Follow the owners manual for installation.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Finish the lower front of the refrigerator with this gray kickplate grille. Its vented design allows air to pass into the machine compartment while covering the base opening and nearby hardware. Cracks, broken clips, or warped sections may leave the grille loose or unable to stay attached. Replacing a damaged or missing grille helps resto...Read morere a neat appearance and secure coverage. Clean dust from the vent openings regularly, and align the retaining clips before pressing the replacement evenly into place to avoid breaking them. This is an OEM part sourced directly from the manufacturer.
This is a replacement pivot block for your refrigerator. It is made of white plastic and is approximately 4 inches long and 1 inch wide. The pivot block catches and holds the door mullion cover when you close the door. If your refrigerator door will not close properly, you may need to replace the pivot block. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Protecting the refrigerator water filter from damage is the job of this white plastic OEM cover. Depress the locking tabs to remove the old cover, then snap the replacement into place. Check your refrigerator model number to confirm fit.
Limit warm air leaks with this gray freezer door gasket. Its flexible magnetic edge seals against the cabinet when the door or drawer closes, helping retain cold air and keep moisture out. Tears, cracks, or warped sections may cause frost buildup, condensation around the door, or longer running times. Replacing a damaged gasket helps rest...Read moreore a snug seal and steady freezer temperatures. Before installation, smooth shipping creases with warm water and clean the retaining channel, then confirm even contact around the full door perimeter. This is an OEM part sourced directly from the manufacturer.
The ice maker thermostat, also known as the cycling thermostat, controls and regulates the ice maker ejection cycle by monitoring the temperature inside the freezer to determine when to release the ice into the bin and start the ice making cycle again. If your ice maker is making unusual noises, or if the ice maker is not making or dispen...Read moresing ice, there could be an issue with the thermostat. Before you begin this repair, make sure the power is disconnected from your refrigerator, and that any food that may spoil is safely stored. This is an OEM part and is sourced directly from the manufacturer. This thermostat is sold individually, and comes with two attachment clips.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
light on to order water filter
916 of 1059 peoplefound this instruction helpful.
Douglas from Byron, NY
Really Easy
Less than 15 mins
Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.
Was this helpful?
Thank you for voting!
Removing the existing filter by rotating as directed and then dislodging from 'docking' station proved difficult. Turns out, the old filter is under a bit of vacuum pressure and getting the unit to separate or release was a challenge.
216 of 335 peoplefound this instruction helpful.
Jake from Novato, CA
Easy
Less than 15 mins
I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate
... Read moremotions and a steady thought process on the problem helped disengage the darned old filter!
Read less
Was this helpful?
Thank you for voting!
Needed to change water filter in refrigerator
163 of 258 peoplefound this instruction helpful.
Marilyn from Lilburn, GA
Really Easy
Less than 15 mins
The switch-out of the water filter was simple with good instructions on the box. The part was delivered very, very quickly!