This manufacturer-approved Refrigerator Pantry End Cap Kit, also known as the Refrigerator Drawer Support, is a kit containing all parts of the Pantry End Cap. It snaps into place on the appliance’s pantry drawer to help contain the items inside and to keep your refrigerator door from sliding all the way out. It is rated as "medium" diff...Read moreiculty to install, is constructed of plastic and comes in white. If broken or missing, the pantry drawer will not stay in place and the part should be replaced. Refer to your user manual and model number to ensure this is the correct part for you. This kit includes both the right and left side end caps, as well as the pins that will hold them in place. To replace an end cap, remove the three screws holding it in place. Then, remove the pin and end cap, replacing the old end cap with the new end cap. In the past, the left and right end caps were sold separately, but the part has been updated and now includes both sides. The part is sold as a kit, and unfortunately, as such none of the parts are available individually.
This OEM Center Rail is a white plastic part which supports the crisper frame, which holds the crisper. Fifteen inches long and white in colour, if broken, the support may no longer hold properly. Refer to your model number and user manual to see if this part will be right for your appliance. This part is a very easy repair which only ta...Read morekes a few minutes and does not require any tools. Just slide the crisper drawers out, lift out the glass shelf, slide the new rale into place and replace the glass shelf and crisper drawers. This part is sold individually and not as part of a set.
Keep pantry foods covered and easy to see with this refrigerator pantry drawer door cover. Its white frame and clear window enclose the drawer while letting you spot meats, cheeses, and snacks at a glance. The hinged lid lifts for access and lowers to cover the storage area. Cracks, broken hinge points, or damaged tabs may leave the lid l...Read moreoose or difficult to move. Replacing a damaged cover restores smooth access and a tidy appearance. Clean it with mild soapy water and a soft cloth. This is an OEM part sourced directly from the manufacturer.
If your refrigerators interior light is not working, the door switch may be the cause. It turns the light off when the door closes. This is an OEM part. Confirm compatibility using your refrigerators model number.
The refrigerator light and fan circuit uses this three-terminal rocker arm switch. It is an OEM replacement part. Disconnect power before working on this electrical part.
Carry defrost water away from the freezer with this refrigerator drain tube kit. It directs melted frost into the drain pan beneath the appliance, where the water can evaporate. The updated curved tube replaces older drain designs that can clog and cause water to back up. A blocked or damaged drain may lead to ice on the freezer floor or ...Read morewater leaking beneath the refrigerator. Installing the kit helps restore proper drainage. Unplug the refrigerator before accessing the lower rear compartment. This is an OEM part sourced directly from the manufacturer.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Maintain a tight seal around the fresh food compartment with this white refrigerator door gasket. Its flexible magnetic edge rests against the cabinet when the door closes, helping retain cold air and block warm, humid air from entering. Tears, cracks, or warped sections may cause condensation, warmer storage temperatures, or longer runni...Read moreng times. Replacing a damaged gasket helps restore proper sealing. Before installation, smooth shipping creases with warm water and clean the retaining channel, then confirm even contact around the entire door perimeter. This is an OEM part sourced directly from the manufacturer.
A warm refrigerator or noisy evaporator fan can indicate a problem with the fan blade. This white, four-blade OEM part circulates cold air over the refrigerators evaporator coils. Confirm fit using your refrigerators model number.
This refrigerator crisper glass shelf insert provides a flat storage surface above the produce drawers and serves as their cover. The clear panel lets you see items below while supporting food containers on top. Cracks, chips, or broken edges may weaken the glass and make the shelf unsafe to use. Replacing a damaged insert restores a comp...Read morelete storage surface. Wear protective gloves when removing broken glass, clear away all fragments, and let cold glass reach room temperature before washing to reduce the risk of cracking. This is an OEM part sourced directly from the manufacturer.
This is a replacement pivot block for your refrigerator. It is made of white plastic and is approximately 4 inches long and 1 inch wide. The pivot block catches and holds the door mullion cover when you close the door. If your refrigerator door will not close properly, you may need to replace the pivot block. This part is sold individually and is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The poorly designed deli drawer lid tab broke off
314 of 351 peoplefound this instruction helpful.
Tim from Littleton, CO
Easy
15 - 30 mins
Nutdriver
Removed the fruit & veggie drawers & the deli (pantry) drawer. Took out the 3 screws, removed the attached parts, put them on the replacement part, reattached it and put the drawers back in.
Here's the part I want to share: PartSelect had a expanded diagram showing the correct part and sufficiently detailed to figure out the
... Read morerepair before the part arrived. That's why I ordered from them. Secondly, I ordered the part Thursday morning--and the thing was sitting on my porch when I came back in from my evening out Saturday--2 days later!!!
Read less
Was this helpful?
Thank you for voting!
Dropped a jug and broke the lower drawer hinge pin
169 of 182 peoplefound this instruction helpful.
Gordon from Cold Spring, KY
Really Easy
Less than 15 mins
Nutdriver
Remove food off of lower shelf, remove the two produce drawers, remove large lower drawer, remove glass shelf, remove three screws holding end cap in place. Once end cap was removed the drawer track could be removed and placed on new end cap. Installation of new end cap took less than 5 minutes. Most of the time spent was removing/repl
... Read moreacing food and cleaning the shelf/bins. PartSelect was awesome BTW!
Read less
Was this helpful?
Thank you for voting!
Crisper frame center rail failure
130 of 145 peoplefound this instruction helpful.
Robert from Meriden, CT
Really Easy
Less than 15 mins
Remove Crisper drawers from Bottom Shelf. Remove glass from the top of Bottom Shelf. Drop new Crisper frame center rail into slots on the top of the Bottom Shelf shelf. Replace glass onto the top of the Bottom Shelf. Slide drawers between left and right guides and the Crisper frame center rail.
Total repair
... Read more time less than one minute. No tools required.