Keep pantry foods covered and easy to see with this refrigerator pantry drawer door cover. Its white frame and clear window enclose the drawer while letting you spot meats, cheeses, and snacks at a glance. The hinged lid lifts for access and lowers to cover the storage area. Cracks, broken hinge points, or damaged tabs may leave the lid l...Read moreoose or difficult to move. Replacing a damaged cover restores smooth access and a tidy appearance. Clean it with mild soapy water and a soft cloth. This is an OEM part sourced directly from the manufacturer.
This refrigerator crisper drawer pan keeps fruits and vegetables contained in a separate storage space within the fresh food compartment. Its clear plastic walls make it easy to see contents and organize produce. Cracks, broken edges, or worn sliding surfaces may cause sticking, spills, or difficulty opening and closing the drawer. Replac...Read moreing a damaged pan helps restore convenient storage and smooth access. Keep the old drawer until installation is complete, as its front trim or handle may need to be transferred to the replacement. This is an OEM part sourced directly from the manufacturer.
The right side of your refrigerator pantry drawer is supported by this white endcap, which snaps onto the drawer. Confirm compatibility with your refrigerators model number. This is an OEM part.
This left-side refrigerator pantry drawer end cap supports the drawer and helps keep it aligned as it slides open and closed. It mounts to the interior wall and provides a connection point for the pantry lid. Cracks, broken tabs, or a damaged lid pin may cause sagging, sticking, or a loose cover. Replacing a damaged end cap restores firm ...Read moresupport and smoother drawer access. Empty and remove the drawer before replacement, and handle the plastic mounting points carefully to avoid bending or breaking them. This is an OEM part sourced directly from the manufacturer.
If your refrigerators interior light is not working, the door switch may be the cause. It turns the light off when the door closes. This is an OEM part. Confirm compatibility using your refrigerators model number.
The refrigerator light and fan circuit uses this three-terminal rocker arm switch. It is an OEM replacement part. Disconnect power before working on this electrical part.
Carry defrost water away from the freezer with this refrigerator drain tube kit. It directs melted frost into the drain pan beneath the appliance, where the water can evaporate. The updated curved tube replaces older drain designs that can clog and cause water to back up. A blocked or damaged drain may lead to ice on the freezer floor or ...Read morewater leaking beneath the refrigerator. Installing the kit helps restore proper drainage. Unplug the refrigerator before accessing the lower rear compartment. This is an OEM part sourced directly from the manufacturer.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Maintain a tight seal around the fresh food compartment with this white refrigerator door gasket. Its flexible magnetic edge rests against the cabinet when the door closes, helping retain cold air and block warm, humid air from entering. Tears, cracks, or warped sections may cause condensation, warmer storage temperatures, or longer runni...Read moreng times. Replacing a damaged gasket helps restore proper sealing. Before installation, smooth shipping creases with warm water and clean the retaining channel, then confirm even contact around the entire door perimeter. This is an OEM part sourced directly from the manufacturer.
A warm refrigerator or noisy evaporator fan can indicate a problem with the fan blade. This white, four-blade OEM part circulates cold air over the refrigerators evaporator coils. Confirm fit using your refrigerators model number.
This is a replacement pivot block for your refrigerator. It is made of white plastic and is approximately 4 inches long and 1 inch wide. The pivot block catches and holds the door mullion cover when you close the door. If your refrigerator door will not close properly, you may need to replace the pivot block. This part is sold individually and is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken pins holding pantry door
149 of 169 peoplefound this instruction helpful.
Gregory from Bethesda, MD
A Bit Difficult
15 - 30 mins
Nutdriver
Removed door and crisper pans. Removed nuts on left end cap - think there were 3. Removed nuts on right end cap and one or two on back air regulator attached to right end cap. Replaced left end cap with new one using reserved nuts. Carefully removed back air regulator from right end cap. Attached back air regula
... Read moretor to new right end cap. Replaced right end cap and back air regulator and attached with nuts. Carefully inserted pantry door into pin on one side and slightly bent both right and left pins to insert door fully into end caps. Replaced crisper pans. That's it.
Water leaking from bottom of refrigerator onto floor
108 of 123 peoplefound this instruction helpful.
Jack from DINUBA, CA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!
Was this helpful?
Thank you for voting!
Lights inside refrigerator not working
138 of 259 peoplefound this instruction helpful.
Clint from Rayville, MO
Really Easy
Less than 15 mins
Screw drivers
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.