During each drain cycle, the pump must move water out quickly so the washer can continue to spin. Humming, grinding, slow drainage, or repeated stopping may indicate a damaged motor or impeller. Inspect and clear the filter and hoses before ordering a replacement. Match the pump to the full appliance model and parts diagram. Disconnect el...Read moreectrical power and water, prepare towels for spills, and avoid running the pump dry. After reassembly, perform a short test while watching every hose connection for leaks.
This is a water inlet valve designed for Samsung washing machines. Water inlet valves are used to control the hot and/or cold water going into the washing machine, and if it is broken or damaged can cause leaking or low water pressure. This water inlet valve connects to the rear of the washing machine and attaches with its five different ...Read moreterminal connections. To replace this water inlet valve, you will need a flat-head and Philips-head screwdriver, and to ensure the water and power to your washer is turned off. This water inlet valve is sold individually and does not come with any wire harnesses or necessary securing screws.
This adjustable leg, also known as a levelling leg, is a genuine OEM part supplied by Samsung for use with washing machines. The leg supports the washing machine by ensuring that it is level and balanced. It is black in color and has dimensions of 3.25 inches in length and 2 inches in width. Over time the leg(s) may wear down or become da...Read moremaged. If your washer is suddenly noisy and it excessively vibrates and shakes during use, then one or more of the legs may be at fault. Each adjustable leg is sold separately.
This is the drain pump assembly for various models of Samsung washing machines. The drain pump is used to remove any water from the washer after it has completed its washing cycle. If your washer still has water left in the tub after it has finished washing this drain pump assembly is likely bad defective or worn out and in need of replac...Read moreing immediately. It is important that you do not use your washer with a bad drain pump as that could lead to further damage to your washer clothes or home. This drain pump assembly is approximately 4.5 inches tall and will require tools such as a wrench and screwdriver to access and replace. This drain pump is sold as an individual OEM part and does not include any securing screws.
This manufacturer-approved screw is for refrigerators, including Kenmore refrigerator model. Avoid cross-threading refrigerator screw during installation.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer stopping in the rinse and spin cycle
5 of 9 peoplefound this instruction helpful.
Gary from CENTER HARBOR, NH
Easy
15 - 30 mins
Screw drivers, Socket set
Tipped the washer up on a couple of chairs. Pulled the motor apart in three pieces and replaced the Hall Sensor. Error code lead me right to the problem and solution.
Was this helpful?
Thank you for voting!
Top Load washer would not drain to complete spin cycle.
10 of 24 peoplefound this instruction helpful.
Greg from Medina, OH
Very Easy
15 - 30 mins
Pliers, Screw drivers
Though I could hear and feel the drain pump running, the washer would not drain. This model does not have a filter for the drain pump. I lowered the discharge hose from the stand up pipe on the wall, and lowered it to the floor. Water ran right out, so no blockage in the drain system. After removing the inlet and outlet hoses to the pump,
... Read more a quick inspection showed the impeller on the motor was off the shaft and flopping around. Bingo, motor runs but cant pump. Ordered from Partselect and received in ONE DAY. I really didn't want to go back to it that soon, but they certainly did their part. Ha. Thank you all. Greg
Read less
Was this helpful?
Thank you for voting!
Washer will not drain
6 of 12 peoplefound this instruction helpful.
Alpha from JACKSONVILLE, FL
A Bit Difficult
1- 2 hours
Pliers, Screw drivers
Went to YouTube video and followed instructions.
Hardest part was making sure water from hose does not flood floor while taking it off from water pump and letting water drain in bucket.