58RIAD Whirlpool Refrigerator - Instructions

Installed new motor control

followed instructions provided when ordering part

first i removed 1 screw, then pulled out the ice maker, unpluged the electrical wire, i removed the white plastic cover , then an additional 3 screws . i pulled off the ice maker control . replaced with new ice maker control. i repeated the steps to put back the ice maker ...so
super quick part delivery !!!

I removed the cover to assembly ,3 screws and it came right off. points were wore out. Thank you for a prompt delivery. It was delivered much faster then I expected.

Paul First time dealing with you ,thanks

Removed the control and motor assembly by removing the plastic cover and three screws. Shut off the power to the refrigerator while removing the control and motor assembly (and also when installing the new one). Tested the motor using an AC power cord. The motor had apparently failed. Ordered the repair part and installed it taking care that the motor drive shaft and shut off arm were correctly aligned. The icemaker began to work properly when power was restored. The cost of this repair was about half the cost of replacing the entire icemaker.

Installed the icemaker control assembly this corrected the problem suspect contacts on the old unit were not making a good contact over time, due to the damp area in the freezer the new unit corrected the repair easy repair.

I had to order the module. It was easy to install. If i could have ordered just the gear and shaft, would have been a lot cheaper. Thanks for the addvise. Bill Paisley

Note: I thought the motor was bad, it was actually one of the gears. Order the motor-gear module. You will probably receive the motor-gear module if you order the motor only.

I removed the hex bolt on the right side of the ice maker. Removed the whole assembly from the refrigerator, diconnecting the cable as I pulled it out. I use a philips screw driver to remove the three scews holding the motor gear assembly. I pulled off the motor/gear module; installed the new motor gear assembly. Reinstalled the ice maker. Easy!

Unplugged the frig., removed three screws, pulled the motor out, then slid the new motor in. Within a few hours I had ice again. The only problem was I felt the motor was still hooked to something after I took out the screws. Just be firm and pull it out, the pressure you feel is the thin bar that slides into the back of it to monitor the level of ice in the tray. It was REALLY easy.

Read on line that the motor module in the ice maker was likely to be the problem. I ordered the part and it came in as a complete module. All I had to do was to remove the cover, take out 3 philips screws, remove the old module and install the new one. I plugged it back in and had ice within the hour.

Open the icemaker service, door slide it out, remove wiring, remove ice maker control cover,remove 3screw, put new one in, put everything back together and with in 6 hours we have ice again. PS my husband did it though.

First I did the diagnostics and thought the water valve wasn't functioning so I replaced that, but it still didn't make ice. So I went on line and found the first thing to fix should have been the module and motor assembly. It was a real easy fix because I had pulled the ice maker before to investigate what was wrong. I just removed one screw and disconnected the electrical. There were four screws holding the motor assembly on. So I put the new motor on and had ice in 30 mnutes.

When I took the ice maker apart I noticed that the shaft of the motor control wheel was broken so when it turned it could not trip the control contacts nor rotate the ice ejector fingers. I ordered a new control and motor assembly which arrived two days later. It was very easy to install and now the ice maker works perfectly.

PartSelect was a great help. A local appliance parts warehouse stocked parts for my ice maker but they only stocked a kit that contained other parts that I did not need. Ordering from PartSelect saved me over $35.

Removed old ejector arm and installed new part.

1. Removed all 4 screws underneath with nutdriver
2. Whole assembly slides out like a drawer
3. Unplugged power/wire harness
4. Removed Motor Assembly - 3 screws
5. Found the broken plastic wheel
6. Ordered part on PartsSelect
(Total: 5 minutes)
7. Received new part next day
8. Put the new motor assembly back on using the original 3 screws (it doesn't come with new ones)
9. Slid unit back into drawer
10. Put the 4 Nut Driver Screws back in (tricky to get the wire harness cover back in place, but not that bad)
11. Plugged in wire harness
12. Turned on the ice-maker
Ice Dropped within the hour.