580675612 Craftsman Generator - Overview

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

This is a genuine part which is supplied directly from the original equipment manufacturer. This leg support is used to stabilize a Briggs and Stratton generator while it is in use. Please refer to the owners manual for instructions on how to install or replace the leg support. This part is made of metal and is sold individually.

The circuit breaker attaches to the control panel and helps to stop overloads. This part is an OEM from Briggs & Stratton generators. This item is sold individually and is made of plastic and metal. A screwdriver might be required during the replacement of this part. It will require replacing if it breaks or burns out.

This rear bearing cover is designed to protect and insulate the rear bearing of the engine. It is an authentic OEM replacement part with a diameter of approximately 8 inches. It comes with a center/dust cap for easy access to the bearing. The cover acts as a barrier that prevents dirt and other contaminants from entering the bearing and p...Read moreotentially damaging it. It also protects the bearing from harsh environmental conditions and keeps it adequately lubricated. Over time, the cover may crack or break, leaving the bearing exposed. A faulty cover will result in several issues such as excessive noise and vibration, increased friction and wear, overheating, and lower overall equipment efficiency. To complete this repair, pry the center cap off first and then detach the old cover from the rear bearing. Clean the mating surface, align the new cover with the bearing, and snap the center cap into position.

This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the exhaust manifold and the cylinder head. This special gasket is available as an individual replacement part, please see model diagram for associative parts.

It is an authentic item that is supplied by original equipment manufacturer, it is specially produced for use on Briggs and Stratton and Snapper generators. This kit is used to secure the engine to the main frame, it is designed to help reduce vibrations from a running engine. Over time the material may deteriorate and get compressed caus...Read moreing the generator to vibrate more than usual, if this happens replacing the mount should resolve the issue. It is a complete kit which includes one metal mount with a rubber pad, a screw, and three locknuts. Please note this replacement kit is sold individually.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

This is a genuine Briggs & Stratton part sourced directly from the manufacturer for use in generators. The outlet is made of metal and plastic and attaches to the control panel. A screwdriver may be necessary during the installation of this item. It may become broken and will need to be replaced. This is available as an individual replacement part.

The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or damaged, the nut and part may be loose and it should be replaced. Check your make, model and diagram to ensure you are choosing the correct part.

This is an OEM part sourced directly from the manufacturer. The circuit breaker boot is commonly found in portable generators from Briggs & Stratton. This part is made of high-quality plastic, and is placed in the control panel to help secure the circuit breaker. You may require a screwdriver when replacing this item. The circuit breaker boot is provided as an individual replacement part.

This connector is sourced from the original manufacturer as a replacement part for use in generators. The connector has 6 pins/terminals which allow the joining of various electrical cables and components in the generator. Over time the connector can break or wear down, rendering it unable to secure components together. This can result in...Read more electrical hazards, overheating, instability, and loose connections. Disconnect the wires/cables connected to the old connector and remove it from the housing. Place the new connector in the housing and reconnect the wires to the appropriate terminals, following the guidelines in your equipment manual.