58-7870-0 (2004) Campbell Hausfeld Compressor - Overview

Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known...Read more to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

The purpose of a gauge is to register the pressure readings inside the tank. This replacement gauge is sourced directly from original equipment manufacturer for use with Campbell Hausfeld air compressors. The dial reads 0-250 PSI. Please note this gauge has a durable metal body and it is sold individually. You should only need a wrench and a thread-sealing tape to complete this repair.

This is an original manufacturer approved replacement air filter assembly which is specially designed for use with Campbell Hausfeld air compressors. Its purpose is to ensure the air that goes into the engine is free of dust and other harmful contaminants, over time it may get dirty and clogged eventually requiring replacement to maintain...Read more good air flow. This part consists of a durable metal housing with a pleated paper filter element.

This OEM Check Valve is an exact replacement for certain air compressors. The purpose of this part is to allow pressurized air into the tank and stop it from flowing back into the pump. It is made of metal, is gold, is not part of a kit or assembly, and is sold individually. When the check valve is defective, the compressor will funcyio...Read moren normally until the tank fills with air. At that point, the pump will try to restart, but the engine will only produce a humming noise. Similarly, if the tank is full of air, the motor will make a humming noise without engaging. This part is located on the tank to the discharge tube and will need to be replaced if broken or worn. You will need a wrench set and a socket set to complete this repair. Customers rate this repair as Easy.

This Power Cord and Plug Assembly is an OEM sourced part for air compressors. It is wired to the electric motor in order to provide power from a standard outlet. This part is black, consists of a metal wire in a rubber insulated cable, and is sold individually. Depending on how worn it is, your compressor may no longer get power or may ...Read morehave sparks coming from it when it needs to be replaced. If you notice any visible damage such as exposed wires, cracks, or frays, it should be replaced. You will need a screwdriver, pliers, and a wrench to complete this repair. Customers rate this repair as Easy.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

It is a genuine manufacturer-supplied item that is made for Campbell Hausfeld air compressors. O-rings are commonly utilized to provide an air-tight seal between connected components. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement. Check the diagrams for your model to ensur...Read moree the correct repair procedure. A screwdriver and a wrench set might be needed to replace this inspection port o-ring.

It is a genuine OEM part that is made for Campbell Hausfeld air compressors. The unloader valve is an important component which allows a user to safely drain the air from the tank. Unfortunately, over time it may wear out or get damaged eventually requiring a replacement to ensure your unit operates properly. Note, this high-quality unloa...Read moreder includes multiple parts however it is sold as an individual component. Check the owner\\\'s manual and the diagrams of your model to ensure the correct installation and application. You will need a wrench set and pliers to perform this repair.

This replacement filter element is an authentic OEM item that is commonly utilized on Campbell Hausfeld air compressors. Its purpose is to filter out dust and debris from contaminating the engine with the air that goes into the carburetor. Please note this felt filter element is sold individually. Replacing it is a very simple task that does not require any tools.

This genuine OEM air compressor intake filter assembly is designed to protect the compressor pump by filtering dust and debris from incoming air. It features a durable plastic housing with a replaceable paper filter element and is suitable for both indoor and outdoor use. The assembly threads directly into the compressor intake and can be...Read more mounted vertically or horizontally, making replacement straightforward. Installing a clean, properly functioning intake filter helps maintain airflow, reduce wear on internal components, and support reliable compressor performance.

Sourced directly from the manufacturer, this plug is an exact replacement part for a variety of air compressors. This part is sold individually, not as part of a kit or assembly. It is gold, made of metal, and will be found on the pressure switch. This part will leak when it has become defective and will need to be replaced if it is dam...Read moreaged or worn. When you install the part, apply Teflon tape to the threads before tightening it in place. You will need a wrench to complete this repair. Customers rate this repair as Easy.