560XP (XPG) Husqvarna Chainsaw - Overview

Genuine Husqvarna replacement part, this part is sold individually. The 503939601 Air Purge does just what the part name says. It purges the air out of the carburetor. Then it forces fuel from the fuel tank and fuel line in to the carburetor.

This is a genuine Husqvarna replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article an...Read mored video on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.

This check valve, also known as a one-way valve, is a genuine OEM part that regulates the flow of fuel/oil in the equipment engine to prevent it from flowing backwards. It is made of plastic and designed for use in a variety of lawn and garden power equipment. If the valve is jammed, worn down, or contaminated with dirt and debris, it wil...Read morel be unable to open and close properly, thus restricting the flow of fuel and compromising the engine combustion process. You will likely notice fuel leaks around the carburetor, engine stalling, hard starting, and overall lower performance from your equipment. To remove the faulty valve, carefully disconnect any hoses or fasteners connected to it. Place the new valve in position and secure it appropriately.

This authentic OEM rim sprocket in your chainsaw transfers power from the engine to the cutting chain. It is typically located at the center of the clutch drum, situated at the end of the engine crankshaft. By engaging with the chain drive links, it enables the chain to rotate and cut through materials as the engine turns. You will notice...Read more that if the rim sprocket is broken that the chain slips, does not engage, or rotates unevenly. It may also reveal signs of wear such as worn-out teeth. Failure to replace a broken rim sprocket can result in reduced cutting power, chain damage, and increased strain on the engine. To remove the rim sprocket, first, loosen the chain tension by adjusting the tensioning screw or knob. Then, remove the guide bar by loosening the nuts or clips on the side cover and sliding the guide bar off the saw. Use a screwdriver or appropriate tool to remove the screws or fasteners securing the clutch cover. With the clutch cover removed, you can access the clutch drum. Hold the drum in place and turn the retaining bolt counterclockwise to loosen it. Carefully slide off the clutch drum. This replacement part is sold individually.

Primarily used in chainsaws, this Starter Rope is an exact replacement part for hundreds of models. It is white and sold individually, not as part of a kit or assembly. The Starter Rope will need to be replaced once you notice signs of it fraying, wearing, or it breaks off. Customers rate this repair as Easy.

This is an authentic replacement part that has been sourced from the original manufacturer to be used with trimmers and chainsaws from Husqvarna. The spark plug is threaded and screws into the cylinder. The plug creates an electric arc that ignites the fuel/air mixture inside the combustion chamber. A spark plug wrench is needed to install this item.

This is a genuine OEM sourced replacement hardware, not an aftermarket imitation. It is specially made for Husqvarna chainsaws. This screw is generally used to secure the starter housing. Please note, this torx screw is sold individually. To install or remove this hardware you can use either a flat-head screwdriver or a torx screwdriver.

This cylinder plug is an original part from Husqvarna. Compatible with many chainsaws, the metal plug is sold individually. Fitted in the cylinder, this item covers the compression hole. Pliers may be required for the installation.

It is an authentic OEM part that is specially made for use with Husqvarna, Poulan, and Jonsered chainsaws. This is an identical replacement for a faulty or a missing pawl that was installed on a new unit. It is a special hardware which helps to engage the flywheel. This high-quality pawl is made of durable metal and is sold as an individu...Read moreal item. Make sure to refer to the appropriate diagrams for your model to ensure the exact location and the correct application. A wrench set will be needed to perform this repair.

This part is an OEM from Husqvarna. The metal spring is made for use with several chainsaws. This item helps to secure the pawl to the flywheel, and is sold individually. A hex key and a pair of pliers are often necessary for the installation.

This replacement nut is high quality hardware that is specially manufactured for use with Husqvarna chainsaws. It has multiple applications depending on your tool, please make sure to check appropriate diagrams for correct location and use of this item. Note this durable metal item is sold individually.