560H Husqvarna Lawn Mower - Overview

The Dust Shield is a 6-3/4 inch, black plastic part, used to prevent dust or debris fouling the wheel or axle. It attaches inside of the wheel around the axle. Installation is rated as "Easy" and will require a wrench. If broken, damaged, or worn due to fatigue, you will see visable damage and you may have debris getting caught in the axl...Read moree. If broken, replace it. Refer to your make, model and diagram to make sure you're choosing the right part. This part comes individually sold.

This genuine manufacturer sourced replacement part is designed for use with lawn mowers.It attached to the mower deck to protect your feet and legs from grass clippings and debris. It is made out of plastic and it is sold individually. Please note the brackets and hardware are sold separately.

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.

The E-Ring 7/16 is a 7/16-inch silver, metal part which can be attached to various locations on a variety of equipment to snap into grooves and secure parts into place. This part will require pliers to install. If broken, damaged or worn, there may be a problem with the part it is securing and the part should be replaced. Refer to your make, model and diagrams to check if this is the right part.

This authentic OEM sourced replacement part that is specially manufactured for use on walk-behind lawn mowers. This cable assembly consists of a durable metal cable with rubber insulation. The purpose of this cable is to stop the blade when the control handle is released on mowers. If the cable is broken it will cause the brake to not rel...Read moreease even when the lever is pressed. Please note this replacement engine zone control cable is sold individually.

This washer is not part of a kit or assembly. It is sold individually. With an O.D. of 1 inch, this OEM replacement part is made of dark grey metal and is used to provide a tight seal between the mower blade and the blade bolt/screw. This part should be replaced if you notice any visible wear, warping, or damage. You will need a wrench or socket set to complete this repair. Customers rate this repair as Easy.

This is a genuine manufacturer-sourced replacement screw which is specially designed for use with Craftsman lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location and use of this item. This part is made of h...Read moreigh-quality metal and it is sold individually, you will need a wrench to secure or remove it.

A genuine item that is supplied by the original equipment manufacturer for use with lawn and garden equipment. It is a high-quality screw which has a few different applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location and application of this hardware. Keep in mind this durable metal component is sold individually.

This is an authentic OEM part for use with Poulan, Husqvarna, Weed Eater, Troy-Bilt.and Jonsered Lawn Mowers. The ground drive belt connects the engine crankshaft to the transaxle pulley to drive the rear wheels. If the belt breaks, the lawn tractor won't move. If the belt is worn, the lawn tractor moves sluggishly because the belt slips ...Read moreon the pulley. This part is sold individually. The tool that you will need to replace the ground drive belt is a socket set.

This is an original part from Craftsman for use with Lawn Mowers. The bail control bar lets you start the engine when you pull the bail control bar against the handle and kills the engine when you release it. The most common reason for replacing the bail arm is if it is damaged. This part is sold individually. There are no tools needed to replace the bail control bar.

This is a genuine Craftsman selector knob that is specifically made for use with a walk behind lawn mower. This selector knob attaches to the adjustment lever giving the user a comfortable grip when adjusting the mower deck to the desired cutting height. This part is made of a durable plastic and is sold individually.

This is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmowers from Husqvarna, Poulan, Weed Eater, and Jonsered. The control lever and cable is used to adjust the engine's output. This item is available as an individual replacement part.