56009 - Overview

This cotter pin is an OEM part that is 1.25 inches long, gold in color, and sold individually. Made of metal, it can have a range of applications on a variety of lawn and garden equipment. Generally, you will need to replace this part if it becomes broken due to age and wear, or if you need to remove it for making other repairs. This is...Read more an easy repair that only requires a pair of pliers to carry out. You need to bend one end around the shaft or bolt and bend the other around the back end of the bolt to complete the repair.

This is a genuine replacement part for tractors made by Snapper, Murray, and Simplicity. The bushing fits between the washer and the mounting steering plate. It is made out of plastic and will need to be replaced if it becomes broken. A screwdriver, a set of pliers, and a wrench set may all be needed to help replace this part. This item is sold individually.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

BOLT, 5/16-18 x 3/4" Short Neck Carriage, GR 5

This metal washer is a genuine OEM part that is commonly used on various lawn equipment and is typically used to secure and seal connected components. This washer is high-quality and is sold individually, so consult with the relevant diagrams for your model to correctly determine where this washer would be for your equipment, and whether you need one, or more.

This is a genuine OEM sourced part which is specially designed for use with Murray, Snapper and Simplicity lawn mowers. It is an identical replacement for a missing or a faulty spring that was installed on a new unit. This high-quality component is made of durable metal and is sold individually. Please make sure to refer to the appropriat...Read moree diagrams of your model for the correct location and application of this spring.

This Hair Pin is a metal, silver, individually sold pin measuring .0915 x 1-7/8. It is used to secure parts in place, or to prevent fasteners from backing out, and can be used in various locations on a variety of equipment. Installation is rated as "Easy" by users and doesn't require any special tools. If broken or damaged, it should be r...Read moreeplaced. Refer to your make, model and diagrams to ensure this is the correct part.

This hex center lock nut is sourced from the original manufacturer for use in lawn and garden power equipment. It is a hexagon-shaped fastener for bolts/studs that is responsible for the keeping the bolt/studs secure during use. The nut is made of metal and has a diameter of 5/16 of an inch and a thread pitch of 18 internal threads per in...Read morech. Over time the threads in the nut can wear down and the nut itself may crack or break. It is important to replace it as soon as necessary to avoid damaging your equipment. Use a socket or wrench to remove the old nut and thread the new one on. Make sure to order the correct number of nuts for your equipment as each nut is sold individually.

It is an authentic OEM sourced item which is specially produced for use with snowthrowers, generators, and rear engine riders made by Murray, Briggs & Stratton, Snapper, and Simplicity. The nut is made of metal and attaches to the starter switch. During replacement, it may require a wrench to help install this part correctly. It may becom...Read moree broken or stripped and will need to be replaced. This part is available as an individual replacement.

The retainer attaches to the idler arm support. This genuine item is supplied by the original equipment manufacturer for use with tractors and rear engine riders made by Snapper, Murray, and Simplicity. It is made out of metal and is sold individually. During the installation process, a wrench set might be needed to replace this part. Over time this part may break and will need to be replaced.