Genuine Husqvarna replacement part, this part is sold individually. The 503939601 Air Purge does just what the part name says. It purges the air out of the carburetor. Then it forces fuel from the fuel tank and fuel line in to the carburetor.
Used to seal the fuel tank to prevent leaks and allow the fuel line to enter through it, this Fuel Tank Bushing is sourced directly from the manufacturer. It is made of black rubber, is not part of a kit or assembly, and is sold individually.
This part will wear through regular use and should be replaced if you notice signs of damage or...Read more wear. When it malfunctions, you will see fuel leaking from the bushing. You will need a screwdriver and pliers to complete this repair.
Customers rate this repair as Easy.
This O-ring is a genuine OEM replacement part designed for use in a variety of power tools. It is a rubber seal used to prevent pressure loss, as well as oil, fuel, and air leakage from the fuel hose. It can be found on either end of the hose. You will need to replace this ring if it has lost elasticity, or if it is cracked or deformed. T...Read morehe O-ring can fail due to age, exposure to heat and chemicals, pressure buildup, or poor installation. A faulty ring will result in leakages, pressure loss, and decreased equipment performance. Carefully pry the old O-ring off the hose. Remove any dirt or debris in the area and lubricate the new ring before placing it in position. Apply light pressure to the ring until it is secure and sitting snugly. Note that your equipment may have several O-rings, therefore, inspect all of them as each ring is sold individually.
This Carburetor Gasket provides a tight seal between the carburetor and insulator. If broken, the engine will run lean due to excess air causing performance issues, and the part should be replaced. If the carburetor has to be taken off for any reason, the gasket should be replaced, as it is one-time use. Installation requires a screw driver and pliers, and is rated as "Easy".
This is an authentic OEM sourced replacement part that is intended to be used with trimmers, brushcutters, and edgers from Husqvarna and Jonsered. The metal nut is used with several different types of machines and the application of the nut can vary based on the model of the equipment. This nut is sold individually.
This is a genuine Husqvarna replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article an...Read mored video on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.
It is an authentic OEM sourced hardware that is commonly utilized on Husqvarna handheld trimmers and blowers. This screw has multiple applications depending on unit, to ensure correct use of this hardware please make sure to check appropriate diagrams. Please note this hex socket head screw is sold individually.
This fuel hose/line that is supplied directly from original equipment manufacturer. It is an authentic part commonly used on Husqvarna trimmers/edgers. The fuel line is connected to an in-tank fuel filter (sold separately) that ensures the gas delivered to the carburetor is free of contaminants. This is a clear plastic fuel line that is sold individually.
Power reaches a trimmer or brush-cutter head through the driveshaft inside the outer tube. Bent metal or worn splines may cause rattling, slipping, poor cutting, or no head movement. Check the clutch and gear head before ordering a replacement because they can create similar symptoms. Match the shaft to the full equipment model and parts ...Read morediagram. Shut off the tool, disconnect the spark plug wire or remove the battery, wear gloves, and make sure both shaft ends engage fully before reassembly and testing.
This is a genuine OEM replacement backing flange which is specially produced for use with Husqvarna trimmers and brush cutters. This part helps to secure the cutter blade to the drive shaft, please make sure to check appropriate diagrams of your model for the correct location and application of this hardware. It is made of high-quality metal and it is sold individually.
This is an authentic replacement part manufactured for use with Husqvarna brushcutters and trimmers. The driver assembly fits on the bottom of the gear case and is used to cover the spindle and bearings. This driver assembly is sold as an individual replacement part.
This is a genuine OEM sourced replacement part used with Poulan hedge trimmers. A spark plug delivers electric current from an ignition system to an internal combustion engine. After time spark plugs will become dirty or fouled. It is a good idea to replace the spark plug once this happens. This item is sold individually. You should gap y...Read moreour spark plug according to the owners manual of the outdoor product you have. You would need a spark plug wrench or a socket wrench to install this component.