535LK Husqvarna Trimmer - Overview

Genuine Husqvarna replacement part, this part is sold individually. The 503939601 Air Purge does just what the part name says. It purges the air out of the carburetor. Then it forces fuel from the fuel tank and fuel line in to the carburetor.

Used to seal the fuel tank to prevent leaks and allow the fuel line to enter through it, this Fuel Tank Bushing is sourced directly from the manufacturer. It is made of black rubber, is not part of a kit or assembly, and is sold individually. This part will wear through regular use and should be replaced if you notice signs of damage or...Read more wear. When it malfunctions, you will see fuel leaking from the bushing. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

The Starter Pawl bridge provides the resistance needed for the starter rope to start the trimming engine. It is an OEM part that attaches inside the recoil assembly. If broken due to weaar or fatigue, the engine will not engaged when the rope is pulled, and the part should be replaced. Installation is rated as easy and requires a screwdrv...Read moreier, pliers and nutdriver. Refer to your make, model and diagram to check if this part is correct. This part is metal, individually sold, and comes in gold.

This O-ring is a genuine OEM replacement part designed for use in a variety of power tools. It is a rubber seal used to prevent pressure loss, as well as oil, fuel, and air leakage from the fuel hose. It can be found on either end of the hose. You will need to replace this ring if it has lost elasticity, or if it is cracked or deformed. T...Read morehe O-ring can fail due to age, exposure to heat and chemicals, pressure buildup, or poor installation. A faulty ring will result in leakages, pressure loss, and decreased equipment performance. Carefully pry the old O-ring off the hose. Remove any dirt or debris in the area and lubricate the new ring before placing it in position. Apply light pressure to the ring until it is secure and sitting snugly. Note that your equipment may have several O-rings, therefore, inspect all of them as each ring is sold individually.

This Carburetor Gasket provides a tight seal between the carburetor and insulator. If broken, the engine will run lean due to excess air causing performance issues, and the part should be replaced. If the carburetor has to be taken off for any reason, the gasket should be replaced, as it is one-time use. Installation requires a screw driver and pliers, and is rated as "Easy".

This is an authentic item that is supplied by the original equipment manufacturer for use with Husqvarna handheld lawn and garden equipment. It is an identical replacement for a missing or a faulty starter pawl that was installed on a new unit. The part is an important component of recoil starter mechanism, please make sure to refer to th...Read moree appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality pawl is made of durable material and is sold individually.

Designed for use in various chainsaws, the E-Ring secures the pivot pin, which holds the handguard. It is an authentic OEM replacement part made of durable black metal and sold individually, not as part of a kit or assembly. When this part malfunctions, you may notice the handle or handguard is loose. At which point, it will need to be ...Read morereplaced. To complete this repair, you will need a pair of pliers. Customers rate this repair as Easy.

This metal OEM-made spring is found in your lawn and garden trimmer. It is attached on the starter pawl bridge and fastened by a starter pawl. This spring provides tension and recoil action, by assisting the recoil starter mechanism and enabling the starter pawl to engage and disengage effectively during engine startup. If you are having ...Read moretrouble starting the engine and the spring shows signs of breaks, stretching, or distortion, it needs to be replaced. Failing to replace the broken spring can render your machine unusable if it cannot start. To remove the spring, you will need a screwdriver and a pair of pliers. Consult your user guide for specific instructions on accessing the spring by detaching the starter cover and the starter pulley assembly. Remember to remove the spark plug before taking out the starter pawl. Unhook the spring from the starter pawl bridge carefully. Please note that this spring is sold individually.

This genuine OEM tank cap is specifically designed for use with Husqvarna gas-powered handheld equipment. It securely seals the fuel tank to prevent leaks and evaporation, helping maintain optimal performance. The cap includes an integrated retainer, which stays attached inside the tank to prevent the cap from getting lost or falling t...Read moreo the ground during refueling. Crafted from durable plastic, this high-quality replacement part is sold individually.

This is an authentic OEM sourced replacement part that is intended to be used with trimmers, brushcutters, and edgers from Husqvarna and Jonsered. The metal nut is used with several different types of machines and the application of the nut can vary based on the model of the equipment. This nut is sold individually.

This is a genuine Husqvarna replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article an...Read mored video on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.

It is an authentic OEM sourced hardware that is commonly utilized on Husqvarna handheld trimmers and blowers. This screw has multiple applications depending on unit, to ensure correct use of this hardware please make sure to check appropriate diagrams. Please note this hex socket head screw is sold individually.