5320 - Overview

This wire harness is a genuine OEM part designed for ceiling fans. The capacitor for this wire harness is red 300VAC, brown 250VAC, and purple 250VAC. The wire harness is responsible for providing power between the internal components of the fan, such as the lights and motor. The harness also organizes and insulates wires for safety and e...Read moreasy access. If your ceiling fan lights are not working, the controls are not responding, or the fan will not start, you will need to replace the wiring harness as it may be damaged or overheating. To begin the repair, remove the motor housing, blades, and fan canopy. Locate the wire harness inside the motor housing and take note of how the wires are connected to each terminal. Disconnect the faulty harness and remove it from the motor housing. Insert the new harness in the housing and connect the wires to the appropriate terminals using your notes from earlier. Reassemble the fan and switch it on to check for functionality.

When the lower panel of a gas grill rattles or pulls away from the cabinet, worn mounting hardware may be responsible. This hardware pack provides the fasteners and washers needed to hold a compatible bottom panel securely in position. Check for loose screws, damaged threads, missing washers, panel distortion, and rust around the mounting...Read more points before ordering. A badly corroded panel or frame may also require replacement. Use the grills full model and serial details to confirm fit. Shut off and disconnect the fuel source, then wait until every surface is cool. Support the panel during installation and start all screws loosely before tightening them evenly.

This is a genuine manufacturer sourced replacement thermometer designed for use with Weber grills. It can be used to measure temperature inside the grill and the temperature of the food. Mounting tab fits into slot in the bezel to secure the position of the gauge. This part is made out metal and it is sold individually. Please note the, bezel is sold separately. Dial reads 150 - 700 degrees F.

This is an authentic Weber replacement part that has been sourced from the original manufacturer to be used with natural gas grills. The brass coupler is used to connect the fuel hose to the natural gas supply. This quick disconnect is sold as an individual replacement part, tools may not be needed to install this item.

It is a genuine replacement o-ring which is supplied by the original equipment manufacturer for use with Dynabrade power tools. This item is utilized to provide an air-tight seal between connected parts, please make sure to check appropriate diagram of your model for the correct use and location of this component. Over time o-rings tend t...Read moreo deteriorate and crack eventually requiring replacement to maintain peak performance. It is a high-quality part that is made of durable rubber material and it is sold individually.

It is a genuine item that is supplied by the original equipment manufacturer for use with Hunter ventilations. The globe/shade is available individually and is made of durable materials. During the installation process, a wrench might be needed to replace this part. It will require replacing if it becomes broken.

This is a Genuine Manufacturer Sourced replacement part used on a variety of Weber Grills. This is a Metal (Aluminum) assembly used to prevent drippings and food particles from marring your deck or patio.

This genuine OEM repair kit is used with Weber grills. This is a four-part assembly that includes two posts and two retaining clips. The posts are designed to hold the lid to the body of the grill while still allowing it to move freely like a hinge.

This is an authentic OEM sourced item, it is not an aftermarket imitation. This high quality bezel is specially designed for Weber grills. This is the bezel for lid thermometer which is also called a temperature gauge. Please note, one metal item is included per order. No tool would be needed to replace this bezel.

This is an authentic OEM sourced replacement part designed for Weber gas grills. This part has a plastic body and it is sold individually. Ignition module produces the spark to ignite the burner. It has two (2) flat connectors. Requires a AA battery (not included). Replacing this Electronic Ignition Module is easy and does not require an...Read morey additional tools • Unplug the wires from the old ignition module • Unscrew the button that holds it to the unit • Place a new module in place • Install a AA battery and secure the module with the button • Connect the wires