Models
>
52198117
52198117 General Electric Washer - Overview
Sections of the 52198117
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Timer Knob Clip
PartSelect #: PS270835
Manufacturer #: WH1X2117
The timer knob clip on your washing machine connects the timer knob to the control panel. If your timer knob is damaged or will not stay in place, you may need to replace the clip. If the timer does n...
$11.00
In Stock
V-Style Drive Belt
PartSelect #: PS270803
Manufacturer #: WH1X2026
This V-shaped drive belt is 29 1/2 inches long x 1/2-inch-wide, and fits both front-load and top-load washing machines. When belts are worn or frayed, they are known to make noise. If you have a top-l...
$14.10
In Stock
Timer Knob with Clip
PartSelect #: PS271127
Manufacturer #: WH1X2757
This part is the replacement timer knob for your washer. It is made of white plastic and is about 1 ¼ inches in diameter. The timer knob sits on the timer shaft and allows you to choose the wash cycle...
No Longer Available
Compression Ring
PartSelect #: PS271609
Manufacturer #: WH2X650
This compression ring works in conjunction with the timer dial.
No Longer Available
Four Port Pump
PartSelect #: PS271344
Manufacturer #: WH23X42
This washing machine pump is white in color and has four ports for water to pass through.
No Longer Available
Agitator Coupling
PartSelect #: PS270786
Manufacturer #: WH1X1944
This coupling is used for 20 spline drive shaft transmissions.
$53.59
Special Order
Hose Clamp Kit
PartSelect #: PS270806
Manufacturer #: WH1X2036
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in ...
$15.89
In Stock
Control Knob
PartSelect #: PS271126
Manufacturer #: WH1X2756
This knob accepts a D-shaped shaft.
No Longer Available
Friction Snubber Pad
PartSelect #: PS270875
Manufacturer #: WH1X2296
This friction snubber pad is an inch and a half long.
No Longer Available
Lower Shaft Seal
PartSelect #: PS273876
Manufacturer #: WH8X281
This seal goes to bottom of the transmission to stop oil from leaking at the bottom of the appliance.
No Longer Available
Levelling Leg
PartSelect #: PS271458
Manufacturer #: WH2X1137
This levelling leg is less than three inches long.
$15.28
In Stock
Questions And Answers for 52198117
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 52198117
[Viewing 7 of 7]Will not agitate
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
GE washer no spinning during spin cycle
Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received i
... Read more
t two days later. Loosened 4 motor mount nuts. Removed old belt and replaced. Tightened belt and tightened nuts on motor. Only tricky part is you will need extensions for socket drive because belt is in the way for two of the motor mount nuts. I used a 1/4" small socket wrench, with an extension. No expertise needed on this one.
Read less
Parts Used:
-
Laurence from Bronx, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
171 of 190 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer was not agitating or spinning
My washer was making noise but not agitating or spinning on any of the cycles that I turned the dial to. Didn't know if it was the transmission or something simple. I did some research and discovered it may be the belt, even though the belt looked new, I changed it anyway by just removing the front of the washer and cutting the belt off a
... Read more
nd putting the new belt on by just turning the pulleys until it fed on. No need to tip it over to do the repair...and it WORKED!! Then I did the happy dance around the house...see woman can repair 2!
Read less
Parts Used:
-
Rachelle from Kent City, MI
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
60 of 64 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced the Agitator coupling
First, you will need to remove the agitator, if it hasn't fallen off by itself. Than, you will need a pulley to remove the coupling from the spinning pole . I used one of those pulleys with three arms to remove it , Second, I lubricated the inside of the new coupling with a little oil, and sided it down on the spinning pole. It was
... Read more
a little hard to installed but, I used a hammer and tapped it in. Third, I also put some lubricant on the new coupling to help the agitator slide down a little easier on the new coupling.
P.S. Check inside agitator for old rubber of the old coupling and remove it. (only if it has fallen off the old coupling.)
P.S. Check inside agitator for old rubber of the old coupling and remove it. (only if it has fallen off the old coupling.)
Read less
Parts Used:
-
jose from lAREDO, TX
-
Difficulty Level:Difficult
-
Total Repair Time:15 - 30 mins
48 of 59 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!