52190117 General Electric Washer Parts & Repair Help | PartSelect
Models > 52190117

52190117 General Electric Washer - Overview

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(12)
PartSelect #:PS270835
Manufacturer #:WH1X2117
The timer knob clip on your washing machine connects the timer knob to the control panel. If your timer knob is damaged or will not stay in place, you may need to replace the clip....
$4.50
In Stock
(6)
PartSelect #:PS270803
Manufacturer #:WH1X2026
This V-shaped drive belt is 29 1/2 inches long x 1/2-inch-wide, and fits both front-load and top-load washing machines. When belts are worn or frayed, they are known to make noise....
$8.90
In Stock
(6)
PartSelect #:PS270305
Manufacturer #:WH13X81
This washing machine water inlet valve has two ports for water to enter.
$26.79
In Stock
(6)
PartSelect #:PS271127
Manufacturer #:WH1X2757
This part is the replacement timer knob for your washer. It is made of white plastic and is about 1 ¼ inches in diameter. The timer knob sits on the timer shaft and allows you to c...
$21.91
In Stock
PartSelect #:PS271609
Manufacturer #:WH2X650
This compression ring works in conjunction with the timer dial.
$14.30
In Stock
(2)
PartSelect #:PS270786
Manufacturer #:WH1X1944
This coupling is used for 20 spline drive shaft transmissions.
$44.37
In Stock
(2)
PartSelect #:PS270806
Manufacturer #:WH1X2036
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of t...
$10.57
In Stock
PartSelect #:PS271126
Manufacturer #:WH1X2756
This knob accepts a D-shaped shaft.
$31.18
In Stock
PartSelect #:PS273876
Manufacturer #:WH8X281
This seal goes to bottom of the transmission to stop oil from leaking at the bottom of the appliance.
$33.95
In Stock
PartSelect #:PS271567
Manufacturer #:WH2X42D
$5.50
In Stock
Questions and Answers for 52190117
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

GE washer no spinning during spin cycle

V-Style Drive Belt – Part Number: WH1X2026
  • Customer: Laurence from Bronx, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 159 of 174 people found this instruction helpful
Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received it two days later. Lo... read more

washer was not agitating or spinning

V-Style Drive Belt – Part Number: WH1X2026
  • Customer: Rachelle from Kent City, MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 58 of 62 people found this instruction helpful
My washer was making noise but not agitating or spinning on any of the cycles that I turned the dial to. Didn't know if it was the transmission or something simple. I did some research and discovered it may be the belt, even though the belt looked new, I changed it anyway by just removing the front of the washer and cutting the belt off and putting the new b... read more

Replaced the Agitator coupling

Agitator Coupling – Part Number: WH1X1944
  • Customer: jose from lAREDO, TX
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 45 of 56 people found this instruction helpful
First, you will need to remove the agitator, if it hasn't fallen off by itself. Than, you will need a pulley to remove the coupling from the spinning pole . I used one of those pulleys with three arms to remove it , Second, I lubricated the inside of the new coupling with a little oil, and sided it down on the spinning pole. It was a little hard to i... read more