52050119 General Electric Washer Parts & Repair Help | PartSelect
Models > 52050119

52050119 General Electric Washer - Overview

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(12)
PartSelect #:PS270835
Manufacturer #:WH1X2117
The timer knob clip on your washing machine connects the timer knob to the control panel. If your timer knob is damaged or will not stay in place, you may need to replace the clip....
$4.50
In Stock
(6)
PartSelect #:PS270305
Manufacturer #:WH13X81
This washing machine water inlet valve has two ports for water to enter.
$26.79
In Stock
(6)
PartSelect #:PS271127
Manufacturer #:WH1X2757
This part is the replacement timer knob for your washer. It is made of white plastic and is about 1 ¼ inches in diameter. The timer knob sits on the timer shaft and allows you to c...
$21.91
In Stock
PartSelect #:PS271609
Manufacturer #:WH2X650
This compression ring works in conjunction with the timer dial.
$14.30
In Stock
(2)
PartSelect #:PS270786
Manufacturer #:WH1X1944
This coupling is used for 20 spline drive shaft transmissions.
$44.37
In Stock
(2)
PartSelect #:PS270806
Manufacturer #:WH1X2036
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of t...
$10.57
In Stock
(1)
PartSelect #:PS271187
Manufacturer #:WH1X484
$6.57
In Stock
PartSelect #:PS266959
Manufacturer #:WE1X1269
This knob will accept a D-shaped shaft.
$40.19
In Stock
PartSelect #:PS270875
Manufacturer #:WH1X2296
This friction snubber pad is an inch and a half long.
$11.78
In Stock
PartSelect #:PS273876
Manufacturer #:WH8X281
This seal goes to bottom of the transmission to stop oil from leaking at the bottom of the appliance.
$33.95
In Stock
Questions and Answers for 52050119
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced the Agitator coupling

Agitator Coupling – Part Number: WH1X1944
  • Customer: jose from lAREDO, TX
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 45 of 56 people found this instruction helpful
First, you will need to remove the agitator, if it hasn't fallen off by itself. Than, you will need a pulley to remove the coupling from the spinning pole . I used one of those pulleys with three arms to remove it , Second, I lubricated the inside of the new coupling with a little oil, and sided it down on the spinning pole. It was a little hard to i... read more

Hot Water side barely running

  • Customer: Anthony from Tyler, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 26 of 29 people found this instruction helpful
First cut off both incoming water supplys. Next remove the water hoses to the inlet. Then remove some of the screws that are holding the back panel on that will give you access to the inlet plate remove those screws and that are holding the inlet in. when you remove the inlet mark the wires take of the water hose and remove inlet now do the opposite to assem... read more

lost all gear oil bottom of transmission

Lower Shaft Seal – Part Number: WH8X281
  • Customer: opal from richmond, KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 26 of 29 people found this instruction helpful
put washer on its side,removed 1cross section,loosened the nut that held on the pulley.
loosened the motor and removed drive belt,removed drive pulley,removed old seal,poured in 90 weight gear oil,installed new seal and done everything else in reverse order.
stood washer upright connected water hoeses,waste water discharge hose,set washer to spinan... read more