51987 Toro Leaf Blower / Vacuum - Overview

The OEM Air Filter is used to stop debris and particles from entering the carburetor and engine, which could cause damage. It is attached in the air filter housing. It comes in black, and is contructed from foam. Installation is rated as "Easy" by customers, and will require a screwdriver. (Tip: You can place the filter in a plastic bag w...Read moreith a bit of oil, remove it, and then squeeze the filter to drain the excess oil. The remaining oil will work as a sticky trap). If the part becomes worn over time, the engine will be hard to start and will run rich. In this case, replace the part. Refer to your make, model and diagram to ensure this is the correct part for you.

This is a rubber primer bulb with a plastic adapter attachment that is used on a variety of lawn and garden equipment models. This bulb attaches to the carburetor and is used to pump gasoline from the fuel tank into the gas chamber of the carburetor. Over time and through regular use, the primer bulb will lose its elasticity and may crack...Read more, requiring it to be replaced. To replace your primer bulb, you simply need to locate the bulb on your machine, unscrew the housing and remove the bulb, and secure the new one. This bulb is sold as an individual part and has a 2.25cm (7/8-inch) outer-diameter and a 3.33cm (1.3125-inch) height.

This replacement fan is an authentic manufacturer sourced part. It is specially designed for use on Homelite and Ryobi blowers. This is the main fan that produces the air flow. Please note washers and lock nut used to secure this fan are all sold separately. This blower fan is made out of black plastic and it is sold individually per orde...Read morer. To complete this repair you will need a screwdriver and a wrench. • Ensure the blower is not powered up • Remove the cover screws • Separate the cover from the housing • Remove the lock nut that secures the fan • Replace old fan with a new one • Reassemble and test the blower

This is a genuine Homelite replacement part, it is sold individually. The Leaf bag is used on the models listed below. It is attached to the main hosing of the blower. When using the leaf bag, you will want to use the tubes of your choosing that are on the part diagram, for the job you are doing

It is a genuine OEM approved component that is specially made for use with handheld lawn and garden equipment. The purpose of this clip is to secure the fuel line, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Unfortunately, over time parts may wear out, get ...Read moredamaged or simply lost eventually requiring a replacement. Please note this high-quality clip is made of durable metal and is sold individually.

This is an authentic OEM sourced component which is specially designed for Ryobi, Homelite and Toro lawn and garden equipment. It is an identical replacement for a missing or a faulty clip that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application ...Read moreof this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.

This is an authentic Toro replacement part that is sourced from the original manufacturer for use with trimmers and blowers. The metal hose clip is used to secure the fuel line to the carburetor connector. This item may require a screwdriver and small nose pliers to install. This item is available as an individual replacement part.

The tubes on leaf blowers guide the suction and airflow created by the blower. This blower tube assembly includes the 2 OEM interlocking tubes that extend the overall reach of the various compatible blowers. These tubes can break, chip, or get damaged and lose their overall blowing and suction capabilities ? at which point they will need ...Read morereplacing. These tubes come together but do not include the necessary tube to connect to the blower itself, which is sold separately. These tubes are made of high-quality black plastic and can be replaced by simply twisting one off the other and twisting the new tube on until a solid click is felt.

This metal OEM wire clamp is a type of fastener that holds hoses or cables together and keeps them from moving while your machine is operating. It is mostly found in lawn equipment to attach its fuel line to the filter. You can tell that the metal clamp is broken if the parts it was securing has become loose or has fallen off. When this h...Read moreappens, your equipment may start leaking and can pose as a safety hazard. To remove the wire clamp, you need a pair of pliers. Grip onto a broken clamp before twisting it counterclockwise to release it from your machine. This item is sold separately.

This phenolic heat insulator is a genuine OEM replacement used in small gas-powered outdoor equipment to act as a heat barrier between the engine and the carburetor. Made from heat-resistant phenolic material, it helps reduce heat transfer to prevent vapor lock and support consistent engine operation, making it an ideal replacement when heat-related performance issues or damaged insulators are present.